manualshive.com logo in svg

Epson Perfection 1200PHOTO, Service Manual

Share
Download
Epson Perfection 1200PHOTO Service Manual Download Page 83

EPSON Perfection1200

Revision B

Appendix

ADF: Disassembly

83

5.

Remove one metal part and 3 screws. (When you remove one of the 
screws, push the release lever to the arrowed direction.

Figure 7-26.  Removing  gears                                                                                                                                    

6.

Remove 6 gears. One of the gear is fixing the hook to the PF roller shaft.

7.

Remove 4 screws (gold, P-tite). When you removing one screw located 
next to the release lever, push the release lever to the arrowed direction. 
After removing screws, remove the black plastic frame. 

Figure 7-27.  Removing the plastic frame

Remove these 6 gears.

Remove this 

metal part.

Remove3 

screws

Remove 2 

screws

Remove 2 

screws

Remove this black 

plastic frame after 

removing screws

Remove this 

screw after 

moving this lever

Summary of Contents for Perfection 1200PHOTO































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands