manualshive.com logo in svg

Epson Perfection 1200PHOTO, Service Manual

Share
Download
Epson Perfection 1200PHOTO Service Manual Download Page 44

EPSON Perfection1200

Revision B

Disassembly and Assembly

Disassembly Procedures

44

4.2.6  Carriage Motor/Timing Belt Removal

1.

Release the carriage lock. (See section 4.2.1)

2.

Remove the document cover. (See section 4.2.2)

3.

Remove the upper cover. (See section 4.2.3)

4.

Remove the carriage unit. (See section 4.2.5)

5.

Remove 2 gold screws (CBS, M3x6), 2 gold screws (CBS, M3x4)and 2 
rear hooks, and remove the shield cover for the main board.

6.

 Remove 2 gold screws (CBS, M3x4) fixing the CR motor unit, and slide the 
CR motor unit into the inside of the scanner body.

7.

Remove CR motor unit cable from the connector of the main board, and 
remove the CR motor unit.

Figure 4-20.  Removing the Shield for the Main Board

Figure 4-21.  CR Motor Unit Removal (1)

Figure 4-22.  CR Motor Unit Removal (2)

CBS (M3x6)

CBS(M3x4)

Shield Cover

Hooks

CBS (M3x4)

Connector

CR Motor 

Unit

Summary of Contents for Perfection 1200PHOTO































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands