Epson EU-T532 Technical Manual Download Page 39 | Manualshive

Page: 39 / 118

background image

3-4

Handling

Rev. A

Confidential

Storage Precautions

❏

Do not store the printer in environments with excessive dust, high temperature, high
humidity, or in direct sunlight.

❏

Before storing the EU-T532/T542 for an extended time, remove the paper and wipe off dirt
and dust; then clean parts such as the

platen

and the

thermal head

of the printer module,

rollers of the cut sheet presenter module with alcohol. After the alcohol evaporates, close
each module and store the unit.

Note:

If you leave the printer with the paper installed, discoloration of the paper and stickiness between the
paper and the

platen

may occur. In this case, replace the paper.

❏

Storing the printer for an extended period with the

platen

closed could cause the platen

rubber to deform and result in defective printing. If the platen rubber is deformed, it can be
restored to its proper shape by feeding paper through the printer. Just feed paper through
the printer until the

platen

works properly; then resume printing.

Opening/Closing Units and Modules

Note:

❏

Do not apply excessive pressure to any operation part; otherwise its function may be damaged because
of deformation or damage of the part.

❏

Apply pressure to each operation part only in the specified direction; otherwise its function may be
damaged because of deformation or damage of the part.

Paper Roll Supply Module

Opening/closing the paper roll hold unit (See Figure 3-2.)

1. Lift the

plate, fixed

upward (in the direction of arrow B) to release the lock with the

shaft,

paper roll

.

2. Pull the

plate, fixed

in the direction of arrow A to open the unit.

3. To close the unit, push it to the

shaft, paper roll

until it stops. At this time, make sure that

the

plate, fixed

is securely engaged with the groove on the

shaft, paper roll

. (Make sure

the unit is not open when it is pulled in the direction of arrow A.)

Printer Module

Opening/closing the platen unit (See Figure 3-2.)

1. Turn the

lever, platen

(green lever) of the printer module in the direction of arrow C to

open the unit.

2. To close the unit, turn the

lever, platen

in the direction of arrow D.

«
...
37
38
39
40
41
...
»

Summary of Contents for EU-T532























































































































Reviews:

No comments

Related manuals for EU-T532

CLP 510N - Color Laser Printer

Brand: Samsung Pages: 270

Bixolon SRP-270

Brand: Samsung Pages: 13

Brand: Xerox Pages: 418

MICROLINE ML310

Brand: Oki Pages: 32

Brand: U-Line Pages: 33

Brand: Stratasys Pages: 68

WorkCentre 7970

Brand: Xerox Pages: 268

4510B - Phaser B/W Laser Printer

Brand: Xerox Pages: 10

Brand: Code Soft Pages: 101

Brand: Ricoh Pages: 84

Brand: Oki Pages: 105

Brand: Samsung Pages: 177

Brand: Epson Pages: 8

Brand: Epson Pages: 20

Brand: Epson Pages: 10

Brand: Epson Pages: 8

Stilus CX9300F Series

Brand: Epson Pages: 44

Brand: Epson Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands