Epson EPL-N2000 Reference Manual Download Page 235 | Manualshive

Page: 235 / 242

background image

reset
To refresh the printer’s memory and erase the current print jobs.

resident font
A font that is stored permanently in the printer’s memory.

resolution
A measure of the fineness and clarity of images produced by the printer
or monitor. Printer resolution is measured in dots per inch. Monitor
resolution is measured in pixels.

RITech
Resolution Improvement Technology. A feature that smooths the jagged
edges of printed lines or shapes.

ROM
Read Only Memory (ROM) is where permanent information is stored.

sans serif font
A font lacking serifs.

scalable font
See outline font.

SelecType
A feature of the printer that allow you to set printer values and control
most of the printer’s function from the control panel.

serif
The small decorative strokes that come off the main lines of a character.

status sheet
A report that lists the printer settings and other printer information.

symbol set
A collection of symbols and special characters. Symbols are assigned to
specific codes in a character table.

TrueType
An outline font format that was developed jointly by Apple Computer
and Microsoft Corporation. TrueType fonts are outline fonts that can be
easily resized for screen display or for printing.

L

Albatross Rev.c

A5 size

Glossary

’96/08/23

DR, pass 0

4

Glossary

«
...
233
234
235
236
237
...
»

Summary of Contents for EPL-N2000



















































































































































































































































Reviews:

No comments

Related manuals for EPL-N2000

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 72

iPF710 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 92

iPF8000S - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

imageRUNNER ADVANCE C9075S PRO

Brand: Canon Pages: 48

Two-Knife Booklet Trimmer-A1

Brand: Canon Pages: 32

Perfect Binder-C1

Brand: Oce Pages: 82

IMAGERUNNER 7095 PRINTER

Brand: Canon Pages: 615

imageRUNNER C3125i

Brand: Canon Pages: 816

SCX 4500W - Personal Wireless Laser Multi-Function...

Brand: Samsung Pages: 113

imageRUNNER ADVANCE 8105

Brand: Canon Pages: 5

imageCLASS MF269dw

Brand: Canon Pages: 32

Brand: Samsung Pages: 158

7400DT - Phaser Color LED Printer

Brand: Xerox Pages: 20

ApeosPort-III C7600

Brand: Xerox Pages: 369

Brand: Lexmark Pages: 2

201021 - P 330N Photo Printer

Brand: Olympus Pages: 79

Brand: SAGEMCOM Pages: 146

Brand: Felix Storch Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands