Epson EL 33 User Manual Download

Page: 77 / 115

This chapter describes installation procedures for the following

common applications:

Lotus 1-2-3 and Symphony, version 2.x (see page 5-3)

Microsoft Windows, version 3.1 (see page 5-4)

Microsoft Word, version 5.0 (see page 5-5)

Quattro Pro, version 2.x (see page 5-6)

WordPerfect, version 5.1 (see page 5-7)

Your Utility diskettes contain VGA utilities and drivers for

additional applications. If you want to install these utilities or

an extended video driver for an application not listed above,

read the README files on your Utility diskettes. These files

will tell you what additional applications are supported and

will describe the VGA utilities.

Installing the Drivers

The information in this guide is organized alphabetically by

application program or operating environment. To install a

particular driver, turn to the page listed above for your

application or environment.

Note

Each of the VGA drivers is designed to work with a specific

version of software. Make sure the driver you select is

compatible with the version of software you are using, or

you may get unpredictable results.

5-2

Installing video Drivers

Summary of Contents for EL 33




















































































































Search results

Summary of Contents for EL 33

Reviews:

Related manuals for EL 33

Brands by name

Popular brands

Epson EL 33, User Manual

Search results

Summary of Contents for EL 33

Reviews:

Related manuals for EL 33

Brands by name

Popular brands