background image

Dell™ OptiPlex™ 160L Service Manual

 

 

 

Removing the Computer Cover

 

Control Panel

 

I/O Panel

 

Power Supply

 

System Board

 

Replacing the Computer Cover

 

 

 

To remove or replace all other 160L components, see the 

160L Systems User's Guide

.

 

 

 

 

Notes, Notices, and Cautions 

 

 

 

 

 

 

       

 

 

 

Information in this document is subject to change without notice. 

© 2003 Dell Computer Corporation. All rights reserved.

 

Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation

 

is strictly forbidden. 

Trademarks used in this text: 

Dell

, the 

DELL

 logo, and 

OptiPlex

 are trademarks of Dell Computer Corporation. 

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation 
disclaims any proprietary interest in trademarks and trade names other than its own. 

Model: MTC2

 

June 2003 Rev. A00

 

NOTE: 

A NOTE indicates important information that helps you make better use of your computer. 

NOTICE: 

A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. 

 

CAUTION: 

A CAUTION indicates a potential for property damage, personal injury, or death.

Summary of Contents for OptiPlex 160L

















Reviews: