manualshive.com logo in svg

Epson EB-940H, User Manual

Share
Download
Epson EB-940H User Manual Download Page 143

No  sound  can  be  heard  from  the  microphone  (EB-955WH/EB-950WH/EB-965H/EB-945H/EB-940H/EB-98H/EB-97H  only)

Check

Remedy

Is the microphone connected correctly?

Disconnect the cable from the Microphone (Mic) input port, and then reconnect the cable.

s

 "Connecting External Equipment" 

p.33

Is the microphone input volume turned down too low?

Adjust the microphone input volume so that sound can be heard.

s

 

Settings

 - 

Mic Input Level

 

p.105

Is Plug-in Power set correctly?

When using a condenser microphone, set 

Plug-in Power

 to On from the menu.

s

 

Extended

 - 

A/V Settings

 - 

Plug-in Power

 

p.106

The  remote  control  does  not  work

Check

Remedy

Is the remote control light-emitting area pointing towards the
remote receiver on the projector during operation?

Point the remote control towards the remote receiver.

s

 "Remote control operating range" 

p.22

Is the remote control too far from the projector?

The operating range for the remote control is about six meters.

s

 "Remote control operating range" 

p.22

Is direct sunlight or strong light from fluorescent lamps shining onto
the remote receiver?

Set the projector up in a location where strong light does not shine onto the remote receiver.

s

 

Settings

 - 

Remote Receiver

 

p.105

Is the correct setting for the 

Remote Receiver

 selected?

Check the 

Remote Receiver

 from the Configuration menu.

s

 

Settings

 - 

Remote Receiver

 

p.105

Are the batteries dead or have the batteries been inserted correctly? Make sure the batteries are inserted correctly or replace the batteries with new ones if necessary.

s

 "Replacing the remote control batteries" 

p.21

I  want  to  change  the  language  for  messages  and  menus

Check

Remedy

Change  the  Language  setting.

Adjust  the  Language  setting  from  the  Configuration  menu.

s

 

Extended

  -  

Language

 

p.106

Problem Solving

143

Summary of Contents for EB-940H






















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands