manualshive.com logo in svg

Epson EB-1751, User Manual, Page: 107 / 146

Share
Download
Epson EB-1751 User Manual Download Page 107

Check

Remedy

Is the image brightness adjusted correctly?

Adjust the 

Brightness

 setting from the Configuration menu.

s

 

Image

 - 

Brightness

 

p.80

Are the cables connected correctly?

Check that all the cables required for projection are securely connected.
Check that no cables are disconnected and that there are no poor contacts in the cables.

s

 "Connecting Equipment" 

p.24

Is the contrast

g

 adjusted correctly?

Adjust the 

Contrast

 setting from the Configuration menu.

s

 

Image

 - 

Contrast

 

p.80

Is the color adjustment set correctly?

Adjust the 

Color Adjustment

 setting from the Configuration menu.

s

 

Image

 - 

Color Adjustment

 

p.80

Are the color saturation and tint adjusted correctly?
(Only when projecting images from a video source)

Adjust the 

Color Saturation

 and 

Tint

 settings from the Configuration menu.

s

 

Image

 - 

Color Saturation

, 

Tint

 

p.80

Images  appear  dark

Check

Remedy

Is the image brightness set correctly?

Adjust the 

Brightness

 and 

Power Consumption

 settings from the Configuration menu.

s

 

Image

 - 

Brightness

 

p.80

s

 

Settings

 - 

Power Consumption

 

p.82

Is the contrast

g

 adjusted correctly?

Adjust the 

Contrast

 setting from the Configuration menu.

s

 

Image

 - 

Contrast

 

p.80

Is it time to replace the lamp?

When the lamp is nearly ready for replacement, the images become darker and the color quality becomes poorer. When
this happens, replace the lamp with a new lamp.

s

 "Replacing the Lamp" 

p.114

Problem Solving

107

Summary of Contents for EB-1751



















































































































































Reviews:

No comments