Epson C32C824461 - UB R03 Print Server Technical Reference Manual Download

Page: 19 / 86

Chapter 1 Product Overview

Product Information

Parts Name and Function

Push button

push

button

provided

perform

the

following

functions.

• Status

sheet

printing

Push

and

hold

the

push

button

for

three

seconds

when

the

printer

ready

for

printing

(paper

set

and

the

power

supply

turned

on);

the

network

parameter

status

printed.

• Setting

initialization

Push

and

hold

the

push

button

and

while

turning

the

power

supply.

Keep

pushing

the

push

button

(about

ten

seconds)

until

the

initialization

start

massage

(Resetting

Factory

Default)

printed.

All

settings

are

reset

the

factory

settings.

USB connector (Parameter Setting)

The

‐

R03

has

USB

connector

set

the

internal

parameters.

• To

connected

with

USB

cable

the

computer

which

the

dedicated

utility

(TMNet

WinConfig

V3)

installed

set

the

internal

parameters.

The USB connector can be used only for setting the network parameter. The USB connector
cannot be used other purposes, such as printing.

Antenna

Push button

USB connector

(Parameter Setting)

Connector to printer

RF module

Summary of Contents for C32C824461 - UB R03 Print Server























































































Search results

Summary of Contents for C32C824461 - UB R03 Print Server

Reviews:

Related manuals for C32C824461 - UB R03 Print Server

Brands by name

Popular brands

Epson C32C824461 - UB R03 Print Server, Technical Reference Manual

Search results

Summary of Contents for C32C824461 - UB R03 Print Server

Reviews:

Related manuals for C32C824461 - UB R03 Print Server

Brands by name

Popular brands