Epson C11C638001 - LQ 300+II B/W Dot-matrix Printer User Manual Download Page 81 | Manualshive

Page: 81 / 120

background image

Paper Handling

Single sheets do not feed properly

Paper does not feed.

Continuous paper may be left in the printer. Remove the
continuous paper. Set the paper-release lever to the single-
sheet position. Insert a new sheet.

Move the paper a little to the left.

Paper feeding is crooked or the paper jams.

Turn off the printer and pull out the paper. Insert a new sheet
straight into the paper guide. Be sure you’re using the right
type of paper. See the paper specifications in the Appendix.
Check to see that the printer cover is closed.

Paper does not eject completely.

Use the

LF/FF

button to eject the page.

Make sure the printer cover is closed.

The paper may be too long. Use paper that is within the
specified range. See the paper specifications in the Appendix.

R

Blackberry REV.D

A5 size

Chapter 3

95/05/08

pass 0

Troubleshooting

3-7

«
...
79
80
81
82
83
...
»

Summary of Contents for C11C638001 - LQ 300+II B/W Dot-matrix Printer

























































































































Reviews:

No comments

Related manuals for C11C638001 - LQ 300+II B/W Dot-matrix Printer

Brand: Canon Pages: 18

MultiPASS MPC190

Brand: Canon Pages: 8

Brand: Oki Pages: 98

Brand: Compuprint Pages: 38

Brand: Oce Pages: 230

Brand: Conceptronic Pages: 127

5470 - X Color Inkjet

Brand: Lexmark Pages: 202

Brand: Dascom Pages: 2

Brand: Lexmark Pages: 60

Brand: Citizen Pages: 32

Brand: Digital Equipment Pages: 122

A1 with AMS lite

Brand: Bambu Lab Pages: 32

All in One Printer

Brand: Epson Pages: 210

aculaser cx37 series

Brand: Epson Pages: 261

AL-MX200 Series

Brand: Epson Pages: 410

AcuLaser CX29DNF

Brand: Epson Pages: 456

AL-MX300 Series

Brand: Epson Pages: 2

Brand: Epson Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands