Epoch WT-PP User Manual Download Page 17 | Manualshive

Page: 17 / 17

Epoch WT-PP User Manual Download Page 17

Contacts us : email :

[email protected]

, Ph: 080-23481364

Error Messages

S.No.

Error

Code

Description

1.

-oC-

If the value of current weight or displacement exceeds the
[Maximum load capacity or Maximum displacement value +
(9 * resolution)], then “OC” is displayed.

2.

oPEn

If the value of load cell exceeds its range or if the load cell
disconnected, “or” is displayed.
Or
If the value of load cell under ranged, “ur” is displayed.

3.

PASEr

If the entered password was wrong then this error message
will display. Please enter the correct password.

4.

U-Err

If the entered value exceeds the limit then this error
message will display. Please enter the correct value.

5.

S-Err

If the entered cal span is not more than the cal zero + 50
value then the system will display this error message.

6.

C-Err

If calibration back not taken then this error message will
display.

7.

C-dIS

Calibration menu access disabled.

«
...
15
16
17

Summary of Contents for WT-PP


















Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands