manualshive.com logo in svg

Epoch WT-PP, User Manual

Share
Download
Epoch WT-PP User Manual Download Page 12

 

Contacts us : email : 

[email protected]

 , Ph: 080-23481364 

 Serial Communication Protocol 

 

 

 
The communication protocols used are a) Request mode b) Dump mode c) Modbus RTU mode d) 
Modbus ASCII mode 

Note: 

Modbus RTU mode implemented and tested with Simply modbus Software, 

Modscan32,Modbus

 tester. 

Communication settings: 

Parity : 

None ; 

Data Bits: 

8 ; 

Stop Bits: 1 ; Flow Control: None 

Baud rate is settable under setup. 

Request Mode: 

If the Communication mode (C-nod), under setup is “rE9” then the below protocol will dump one 
time based on the request from PC. 

Baud rate is settable under setup.

 

 

 

For Error condition weight value,

 

Over Range (

OR)

Weight value is 99999. 

Over Capacity (

OC)

Weight value is 88888. 

Under Range (

UR)

Weight value is 77777.

 

Dump Mode: 

 

If the Communication mode (C-nod), under setup is “dUmp” then the below protocol will dump 

continuously (Same as request mode response).

  Baud rate is settable under setup.

 

 

 

 

 

 

 

%XX[YZWWWWW]$  

 

 

Summary of Contents for WT-PP


















Reviews:

No comments

Brands by name

Popular brands

Load more brands