EP Equipment EPL153 Operation Manual Download Page 6

Page: 6 / 48

G Pallet Truck Maintenance ....................................................................................................G1

1.1 Operational safety and environmental protection ...............................................................G1

1.2 Maintenance safety regulations ..........................................................................................G1

1.3 Servicing and inspection.....................................................................................................G2

1.3.1Maintenance checklist ......................................................................................................G3

1.3.2 Lubrication points ............................................................................................................G4

1.4 Maintenance Instructions....................................................................................................G6

1.4.1Prepare the truck for maintenance and repairs ................................................................G6

1.4.2 Remove the cover ...........................................................................................................G6

1.4.3 How to add oil ..................................................................................................................G7

1.4.4 How to add grease ..........................................................................................................G7

1.4.5 Checking the fuses ..........................................................................................................G7

1.4.6 Recommissioning ............................................................................................................G8

1.5 Decommissioning the industrial truck .................................................................................G8

1.5.1 Prior to decommissioning ................................................................................................G8

1.5.2 Restoring the truck to operation after decommissioning .................................................G8

1.6 Safety checks to be performed at regular intervals and following any unusual incidents G9

1.7 Final decommissioning, disposal ........................................................................................G9

1.8 Tire replacement .................................................................................................................G9

H Troubleshooting ...................................................................................................................H1

Pg.

Summary of Contents for EPL153

















































Search results

Summary of Contents for EPL153

Reviews:

Related manuals for EPL153

Brands by name

Popular brands

EP Equipment EPL153, Operation Manual

Search results

Summary of Contents for EPL153

Reviews:

Related manuals for EPL153

Brands by name

Popular brands