EP Equipment EPL153 Operation Manual Download Page 43

Page: 43 / 48

REV. 10/2019

How to add grease

Prepare the truck for maintenance and

repairs (See Maintenance Instructions ).

Remove the front panel.

Add grease of the correct grade

(See Lubrication point ).

Add transmission oil every 500 operating

hours, or at least annually.

Re-installation in the reverse order.

Checking the fuses

Fully lower the forks.

Press the emergency stop switch.

Remove the electrical cover(See section

battery removal and installation

)

Fuse 5A installed on main harness. If

necessary, replace it with fuse that match

the parameters specified in the table below

Item

To protect:

Rating

Wire harness

•

WARNING

•

How to add oil

It is necessary to add hydraulic oil when

you heard explosion sound from pipe during

lifting.

Prepare the truck for maintenance and

repairs (See Maintenance Instructions).

Remove the hydraulic cover.(See

Section1.4.2).

Add hydraulic oil of the correct grade (See

Lubrication point

Add hydraulic oil till you can't hear

explosion sound during lifting any more.

Re-installation in the reverse order.

It is forbidden to add hydraulic oil with

impurity.

1.4.3

1.4.4

1.4.5

Summary of Contents for EPL153

















































Search results

Summary of Contents for EPL153

Reviews:

Related manuals for EPL153

Brands by name

Popular brands

EP Equipment EPL153, Operation Manual

Search results

Summary of Contents for EPL153

Reviews:

Related manuals for EPL153

Brands by name

Popular brands