background image

www.enware.com.au 

Call 1300 369 27     19  

product warranty for Australia     

Effective 27 September 2021

Enware Australia Pty Limited (ACN 003 988 314)  

(“we” or “us”) warrants that this product (also referred 

to as “our goods”) will be free from all defects in 

materials and workmanship for 12 months* from the 

date of purchase. Our liability under this warranty is 

limited at our option to the repair or replacement of 

the defective product or part, the cost of repair of the 

defective product or part or the supply of an equivalent 

product or part, in each case if we are satisfied the 

loss or damage was due to a defect in the materials or 

workmanship of the product or part. All products must 

be installed in accordance with the manufacturer’s 

instructions, the PCA, and AS/NZS3500 including any 

other applicable regulatory requirements.

exceptions

This warranty does not apply in respect of any damage or 

loss due to or arising from:
a) Failure by you or any other person to follow any 

instructions for use (including instructions and directions 

relating to the handling, storage, installation, fitting, 

connection, adjustment or repair of the product) 

published or provided by us;
b) Failure by you or any other person responsible for the 

fitting, installation or other work on the product to follow 

or conform to applicable laws, standards and codes 

(including the AS/NZ 3500 set of Standards, all applicable 

State and Territory Plumbing Codes, the Plumbing Code 

of Australia and directions and requirements of local and 

other statutory authorities); or
c) Any act or circumstance beyond our control including 

faulty installation or connection, accident, abnormal use, 

acts of God, damage to buildings, other structures or 

infrastructure and loss or damage during product transit 

or transportation.

making a claim

To make a claim under this warranty you must  

notify us in writing within 7 days of any alleged defect 

in the product coming to your attention and provide 

us with proof of your purchase of the product and 

completed the Online Product Service and Warranty 

Form available on website www.enware.com.au/

warranty-service-form. 

All notifications and accompanying forms must be sent to 

us marked for the attention of the Enware Australia Pty 

Limited, 9 Endeavour Road, Caringbah NSW 2229. We 

can also be contacted by telephone (1300 369 273) or by  

email ([email protected]). 
Your costs in making a claim under this warranty, 

including all freight, collection and delivery costs, are 

to be borne and paid by you. We also reserve the right 

at our cost to inspect any alleged defect in the product 

wherever it is located or installed or on our premises.

* Conditional Warranty:
Water chiller: 12 months parts and labour
Bottler filler: 10 years (2 years parts and labour, then 8 

years parts only warranty)

other conditions

Except as provided or referred to in this document, we 

accept no other or further liability for any damages 

or loss (including indirect, consequential or economic 

loss) and whether arising in contract, tort or otherwise. 

Any benefits available to you under this warranty are in 

addition to any non-excludable rights or remedies you 

may have under applicable legislation, including as a 

“consumer” under the Australian Consumer Law. To that 

extent you need to be aware that: Our goods come with 

guarantees that cannot be excluded under the Australian 

Consumer Law. You are entitled to a replacement or 

refund for a major failure and for compensation for any 

other reasonably foreseeable loss or damage. You are 

also entitled to have the goods repaired or replaced if 

the goods fail to be of acceptable quality and the failure 

does not amount to a major failure.

Summary of Contents for DFSA121-PBBF





















Reviews: