Environmental Express Oakton 300 Series Instruction Manual Download Page 10

Page: 10 / 62

Contents

Data storage.......................................................................27

Data display .......................................................................27

Data management..............................................................28

Data transfer to PC ............................................................29

Print data ............................................................................30

Setup ................................................................................... 32

ID Setup ..............................................................................32

General Setup ....................................................................33

pH Setup.............................................................................35

COND, TDS, Sal Setup ......................................................36

DO Setup ............................................................................38

Maintenance and storage .................................................. 39

Maintenance and storage of the instrument ...................39

Maintenance and storage of pH sensor ..........................40

Maintenance and storage of the EC sensor....................41

Maintenance and storage of the DO sensor ...................42

Error messages and trouble shooting ............................. 44

Appendix............................................................................. 46

Specification ......................................................................46

www.calcert.com

[email protected]

1.800.544.2843

Summary of Contents for Oakton 300 Series































































Search results

Summary of Contents for Oakton 300 Series

Reviews:

Brands by name

Popular brands

Environmental Express Oakton 300 Series, Instruction Manual

Search results

Summary of Contents for Oakton 300 Series

Reviews:

Brands by name

Popular brands