background image

29

Warranty

17. Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and 

residues left on the plated surfaces from the use of abrasive cleaners or polishes is not covered in this 

warranty. 

18. The paint on the Metal Brick Liner may peel. This is due to the extreme conditions applied to the paint 

during normal usage. It is not a flaw and is not covered under warranty.

19. Sherwood Industries Ltd. is free of liability for any damages caused by the fireplace or stove, as well as 

inconvenience expenses and materials. The Limited Warranty does not cover incidental or consequential 

damages.

20. The Limited Warranty does not cover any loss or damage incurred by the use or removal of any 

component or apparatus to or from the Enviro fireplace or stove without the express written permission 

of Sherwood Industries Ltd. and bearing a Sherwood Industries Ltd. label of approval.

21. Any statement or representation of Enviro products and their performance contained in Enviro 

advertising, packaging literature, or printed material is not part of the Limited Warranty.

22. The Limited Warranty is automatically voided if the fireplace or stove’s serial number has been removed 

or altered in any way. If the stove is used for commercial purposes, it is excluded from the Limited 

Warranty.

23. No dealer, distributor, or similar person has the authority to represent or warrant Enviro products beyond 

the terms contained within the Limited Warranty. Sherwood Industries Ltd. assumes no liability for such 

warranties or representations.

24. Sherwood Industries Ltd. will not cover the cost of the removal or re-installation of the stove, hearth, 

facing, mantels, venting or other components.

25. Labour to replace or repair items under this Limited Warranty will be covered per our warranty service 

fee reimbursement schedule. Labour rates are set per component and as such total labour costs may 

not be covered.

26. Sherwood Industries Ltd. is not liable for freight or labour on any stove replaced in-field and is not liable 

for travel costs for service work. In the event of in-home repair work, the customer will pay any in-

home travel fees or service charges required by the Authorized Dealer.

27. At no time will Sherwood Industries Ltd. be liable for any consequential damages which exceed the 

purchase price of the unit. Sherwood Industries Ltd. has no obligation to enhance or modify any 

stove once manufactured (example: as a stove evolves, field modifications or upgrades will not be 

performed). 

28. This Limited Warranty is applicable only to the original purchaser and it is non-transferable.

29. This warranty only covers Enviro products that are purchased through an authorized Enviro dealer.

30. If for any reason any section of the Limited Warranty is declared invalid, the balance of the warranty 

remains in effect and all other clauses shall remain in effect.

31. The Limited Warranty is the only warranty supplied by Sherwood Industries Ltd., the manufacturer 

of the stove. All other warranties, whether express or implied, are hereby expressly disclaimed and 

purchaser’s recourse is expressly limited to the Limited Warranty.

32. Sherwood Industries Ltd. and its employees or representatives will not assume any damages, either 

directly or indirectly, caused by improper usage, operation, installation, servicing or maintenance of this 

stove.

33. Sherwood Industries Ltd. reserves the right to make changes without notice. Please complete and mail 

the warranty registration card and have the installer fill in the installation data sheet in the back of the 

manual for warranty and future reference.

34. Sherwood Industries Ltd. is responsible for stocking parts for a maximum of seven (7) years after 

discontinuing the manufacture or incorporation of the item into its products. An exception to this would 

be if an OEM supplier is not able to supply a part.

=

Summary of Contents for M-55C-FS































Reviews: