Enviro EG-40 Owner'S Manual Download Page 14

 

INSTALLATION OF LOG SET and EMBERS 

 
INSTALLING THE GLOWING EMBERS 

 
A bag of ceramic fiber embers is provided for use on the front burner ember tray. 
 
CAUTION:  Use only the type of ember material supplied with this appliance.  Due to the irregular size of the 
ember material there may be more than required.  Use only a single layer.  Do not pile embers.  The use of other 
foreign materials on the burners may create dangerous conditions. 

 

If over time, through cleaning and servicing, these embers require replacement, contact your nearest ENVIRO 
dealer for replacement embers. 
 
Gently remove the ember material from the plastic bag.  Spreading pieces evenly across the front of the ember 
tray. 
 
Do not pack the embers down leave embers loose. 
 

DO NOT PLACE EMBERS ON THE REAR BURNER. 

 
 
 

CAUTION: NEVER OPERATE THIS APPLIANCE WITH THE DOOR REMOVED 

 

INSTALLING THE LOGSET 

 
Carefully remove logs from box. Check to ensure 
there is no damage. It is very important to install 
these logs in their correct position to insure safe, 
optimum operating conditions. Open the door of the 
fireplace. Place the logs on the log supports. Close 
the door and tighten securely 

 

 

Upon the first light up, watch for ignition to 

all

 burner 

ports. If a long delay is noted: First let the unit cool down. 
Open the door of the fireplace. Carefully reposition the 
embers making sure that the burner ports are not plugged 
or blocked (See adjusting venturi section to adjust air for 
proper flame). 

IMPORTANT NOTE: 

When the unit is 

turned on for the first time, it should be turned onto high 
without the fan on for the first 4 hours. This will cure the 
paint, logs, gasket material and the other products used in 
the manufacturing process. It is advisable to open a 
window or door, as the unit will start to smoke and can 
irritate some people. After the unit has gone through the 

first burn, turn the unit off including the pilot, let the unit get cold then open the glass door and clean it with a good 
gas fireplace glass cleaner, available at your local ENVIRO dealer. (See page 16. Glass Cleaning.)     
 
 
 
 
           

  

 

 

 

14

Summary of Contents for EG-40



























Reviews: