Enviro 828 BV. INS. Page 19 Owner'S Manual Download

Page: 19 / 20

16. INSTALLATION DATA SHEET

The following information must be recorded by the installer for warranty purposes and future reference.

Envirogas Model:

EG-828 INSERT BV. FPI

Name of Owner:

__________________________________________

Address:

__________________________________________

__________________________________________

Phone:_____________________________________

Name of Dealer:

___________________________________________

Address:

___________________________________________

Phone: ___________________________________

Name of Installer:

___________________________________________

Address:

___________________________________________

Phone :_____________________________________

•

Model
:___________________________________

•

Serial Number: __________________

•

Date of Purchase:

__________/________/________

•

Date of Installation:

__________/________/________

•

____ Natural Gas (Nat.), ____ Propane (LPG)

•

Inlet Gas Supply Pressure: ________ in.w.c.

If the orifices were changed by the installer.

•

Front Burner Orifice # __________ ,

Back Burner Orifice # ________ .

•

Pilot Orifice # ________ or ______ in.Dia.

Installer's Signature

E-MAIL ADDRESS (

envirofire@home

.com)

WEB SITE ADDRESS ( www. Enviro-fire.com )

MANUFACTURED BY:

SHERWOOD INDUSTRIES, 6782 OLDFIELD RD., SAANICHTON, B.C., CANADA V8M 2A3

Summary of Contents for 828 BV. INS.





















Search results

Summary of Contents for 828 BV. INS.

Reviews:

Related manuals for 828 BV. INS.

Brands by name

Popular brands

Enviro 828 BV. INS., Owner'S Manual

Search results

Summary of Contents for 828 BV. INS.

Reviews:

Related manuals for 828 BV. INS.

Brands by name

Popular brands