background image

SAFETY PRECAUTIONS

  

FOR SAFE INSTALLATION AND OPERATION OF YOUR "ENVIROGAS"  ROOM HEATER, PLEASE, CAREFULLY 
READ THE FOLLOWING INFORMATION: 
 

• 

All "ENVIROGAS" gas-fired appliances must be 

installed in accordance with these instructions.  
Carefully read all the instructions in this manual first.  
Consult the building authority having jurisdiction to 
determine the need for a permit prior to commencing 
the installation. 
 

• 

NOTE 

Failure to follow these instructions could 

cause a malfunction of the fireplace that could result 
in death, serious bodily injury, and/or property 
damage.   

• 

Failure to follow these instructions may also void 

your fire insurance and/or warranty. 
 

GENERAL 

• 

Installation and repair should be done by a 

qualified service person.  The appliance 
should be inspected before use and at least 
annually by a qualified service person.  More 
frequent cleaning may be required due to 
excessive lint from carpeting, bedding 
material, etc.  It is imperative that control 
compartments, burners and circulating air 
passageways of the appliance be kept clean. 
 

• 

Due to high temperatures the appliance 

should be located out of high traffic areas 
and away from furniture and draperies. 
Children and adults should be alerted to 
hazards of high surface temperatures and 
should stay away to avoid burns or clothing 
ignition. 
 

• 

Young children should be carefully 

supervised when they are in the same room 
as the appliance.   
 

• 

Clothing or other flammable material 

should not be placed on or near the 
appliance.   

 
FOR YOUR SAFETY

 

• 

A qualified installer, service agency or the gas 

supplier must perform installation and service. 
 

• 

This installation must conform with local codes or, 

in the absence of local codes with the current 

CAN/CGA -B149 installation code in Canada or 
the National Fuel Gas Code ANSI Z223.1.2 in the 
USA. 
 

• 

To prevent injury, do not allow anyone who is 
unfamiliar with the operation to use the stove.   

 

• 

Always keep the area around these appliances 

clear of combustible material, gasoline or other 
flammable vapors and liquids.   
 

• 

These appliances should not be used as a 

drying rack for clothing or for hanging Christmas 
stockings or decorations. 
 

• 

Due to the paint curing on the stove a faint 

odor and slight smoking will likely be noticed 
when the stove is first used.  Open a window 
until the slight smoking stops. Always connect 
this gas stove to a chimney and vent to the 
outside of the building envelope.  Never vent to 
another room or inside a building. Make sure you 
use the vent pipe that is specified. Make sure that 
the vent is properly sized and is of adequate 
height to provide the proper draft.  Inspect the 
venting system annually for blockage and any 
signs of deterioration. 

 

• 

 Do not operate with cracked or broken glass.  

Under no circumstances should this appliance be 
modified.  Parts that have to be removed for 
servicing must be replaced prior to operating this 
appliance.  Only parts supplied by ENVIROGAS 
should be used in this appliance and replacements 
should only be performed by a licensed or 
qualified service person.  

 

• 

Never use solid fuels such as wood, paper, 

cardboard, coal, or any other flammable liquids 
etc., in this appliance. 
 

• 

Do not use this heater if any part has been 

under water.  Immediately call a qualified service 
technician to inspect the heater and to replace 
any part of the control system and any gas 
control which has been under water. 
 

• 

Do not abuse glass by striking or slamming 

door shut 

 

2

Summary of Contents for 828 BV. INS.





















Reviews: