background image

3)

 

CONTROL PANEL WITH ON / OFF RADIO CONTROL: 

 

This  is  an  accessory  available  on  all  three-phase  pump  models  (except  EURO  20).  On  models  with  electronic 
variator, a specific radio remote control is provided. The ON / OFF radio remote control simply allows the pump 
to be switched on and off remotely, even if the direction and speed can not be changed. On the control panel there 
is a selector for the operation of the machine with radio control, or with local commands. The direction of travel 
and speed (on models with mechanical or double speed variator) must be set on the control panel. 
In the case of a pump with an electric variator, the remote control has the function of switching on, switching off, 
varying the speed, changing the direction of rotation. On the pump control panel there is a selector to control the 
machine remotely or with the commands on it. 

 

The maximum distance of use varies according to the rooms in which it is used. It is advisable to perform signal 
tests before using the pump.

 

 

4)

 

PANEL WITH SETTING TIMER: 

 

 

Available on all models with three-phase motorization. 

 

FUNCTIONING: 
 

After starting the engine, priming takes place after a few moments; if more than 10/13 seconds pass, turn off the 
engine and disconnect the power cable, check the correct fixing, and the lack of holes in the supply pipes as they 
can  cause  air  infiltration.  If  the  machine  is  provided  with  by-pass,  it  is  possible  to  act  on  this  valve  in  order  to 
increase (valve closed) or decrease (valve open) the flow rate as you want.  

IMPORTANT: the by-pass must be closed at the beginning of processing and for the suction of solid parts. 

To switch off the machine, simply position the engine switch on the "center zero". 
In the  event  of  an emergency stop,  it is  necessary  to  restart the machine  in  the reverse direction  of rotation, and 
immediately  reverse  the  rotation,  thus  allowing  the  elimination  of  any  bodies  that  prevent  the  rotation  of  the 
impeller. 
 
 
 
 
After the use, it is necessary to wash the machine in order to preserve its mechanical and hygienic characteristics. 
It is necessary to run the machine for a few minutes with clean water, proceeding then with the complete emptying 
of the liquid contained in the pipes and in the pump body. For sanitization, use warm water with clinical solutions 
for washing and sanitizing, with concentrations compatible with the rubber components of the machine. 
If a lasting stop of the machine is expected, it is advisable to introduce a few drops of glycerine oil into the pump, 
then reactivate the pump for a few seconds. 
 
Maintenance: all the pump  components are checked and adjusted  in the factory before shipping.  So the machine 
does not need any special maintenance, but only regular checks over time, which also increase the duration of the 
machine.

 

IMPORTANT:

 

These checks must be carried out by qualified personnel and with the machine disconnected 

from the power supply. 

The checks to carry out are the following: 

 

 Check the impeller wear 

4. CLEANING AND MAINTENANCE 

Summary of Contents for EURO 20
















Reviews: