EnOcean LEDD Installation Manual Download Page 8

Page: 8 / 8

LED Zone Controller 0-10V Installation Guide

Page 8

Parameter

Description

Default /

Notes

System Parameters

MinVoltageLevel

Minimum 0-10V output voltage

level when light is switched ON

1.0V

MaxVoltageLevel

Maximum 0-10V output voltage

level when light is switched ON

10.0V

ModeAfter-

PowerLoss

ModeAfterPowerLoss

(ON/OFF/LAST STATE)

LAST STATE

StatusMessage-

Timer

Defines, how often status messages

are transmitted (seconds, 0=off,
0xFFFF=only event based)

0xFFFF

RepeaterFunction

Defines the repeater level of the

device (OFF/1-Level/2-Level)

OFF (disabled)

RepeatLinked-

DevicesOnly

Configures the repeater to only

repeat telegrams from devices
linked to it

ON (enabled)

Enable-

DebugMessages

Enable or disable debug messages

OFF (disabled)

EnableLink-

Checker

Enable or disable link checker

(if a learn telegram from a linked
device is received while in
operating mode, the 0-10V output
will toggle once between 10% and
90%)

ON (enabled)

Summary of Contents for LEDD









Search results

Summary of Contents for LEDD

Reviews:

Brands by name

Popular brands

EnOcean LEDD, Installation Manual

Search results

Summary of Contents for LEDD

Reviews:

Brands by name

Popular brands