manualshive.com logo in svg

Eno Scientific Well Watch 700, User Manual

Share
Download
Eno Scientific Well Watch 700 User Manual Download Page 6

be displayed on the screen. If the measured distance is not as expected, 
then proceed to the next step to change the initial settings.

7.

   

Change initial settings

.  Press the SET button once to enter the settings 

mode. Press the UP or DOWN button to scroll through the available settings. 
To change a setting, press ENTER to start the number flashing, press the UP
or DOWN button to change  as desired, then press ENTER to enter the new 
setting and stop the flashing. Press the UP or DOWN button to continue to 
scroll through the other available settings. Press DISP at any time to return to
read the measured depth. For best depth results, the R

ange Min

, R

ange 

Max

, and the W

ell Temperature

 should all be set. 

8.

Read 

other information

.  While reading the depth display, press the UP or DOWN

buttons to read other information. 

We encourage you to read the frequently asked questions section. They really are 
frequently asked. Also, visit our website 

www.enoscientific.com 

for the latest manual 

and installation tips.

 

  Eno Scientific  Well Watch 700

Page 

6

   

Summary of Contents for Well Watch 700
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands