background image

WARRANTY INFORMATION

It is imperative that when calling Engler Engineering regarding the operation of your 

unit, that you have the serial number available for quick reference. 

The Son-Mate II, scaler polisher combination, with attachments, is warranted to be free 

from material and manufacturing defects to the original consumer / purchaser for a period as 
specified below. 

The Son-Mate II control box is warranted for a period of six (6) years from date of purchase.

The scaler handpiece is warranted for a period of two (2) years from date of purchase.
The Micromotor is warranted for a period of one (1) year from date of purchase.
The polishing straight handpiece is warranted for a period of one year from date of purchase.
Stacks (transducer) are warranted for a period of six (6) months from date of purchase.
Scaling tips are warranted for a period of thirty (30) days from date of purchase. 
Prophy warranted for a period of thirty (30)
days from date of purchase.  

All warranties are void if the items have been damaged due to negligence, improper use, 
failure to lubricate, removed parts, or opening the control unit. 

PLEASE NOTE: 

Whenever returning any products for evaluation and / or repair, we strongly suggest you send 
in the complete unit with all attachments so that a correct evaluation can be made. 

Engler Engineering Corp, has been in business since 1964, in Hialeah, Florida, building and 
maintaining dental units and parts for our ultrasonic scalers, polishers, and anesthesia machines 
as well as manufacturing inserts and other items for many devices on the market today. As a 
leader in the field, we would appreciate a minute of your time to let us know how we can better 
serve you.

You can mail all comments, suggestions and questions to us at the following address and number: 

Engler Engineering Corp. 1099 East 47 Street Hialeah, FL 33013 

If you wish to fax to us, please use 305-685-7671.

 

 

Page 29 of 31

Summary of Contents for Son-Mate II
































Reviews: