ENFORCER Auto Dialer
6
SECO-LARM U.S.A., Inc.
Programming the Auto Dialer:
The setup mode may only be accessed when the dialer is in standby mode. If no key is pressed
within 15 seconds, the dialer will automatically exit the setup mode.
Setting and Changing the PIN Number
1.
Enter the current PIN number (factory preset PIN number is
‘000’
), and press the [PROG]
button once. ‘PASSWORD’ will flash on the LCD.
2.
Press the [ARM/DISARM] button to accept.
3.
Enter a new PIN number (3-6 digits) followed by the [ARM/DISARM] button to confirm.
4.
Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
Example 1
– To store a number with area code 1-214-555-2858 and an office extension 205
(where the PBX requires a 2-second pause before the extension): After scrolling to the desired
number location, enter ‘12145552858,’ press the [DEL/PAUSE] button for 2 seconds until the
letter ‘F’ appears on the LCD screen, enter ‘205’ and press the [ARM/DISARM] button.
Note:
If the PIN number is forgotten, press and hold the [PROG] button and use a pen or
paper clip to press the [RESET] button located under the cable cover on the back of the unit
and release. The unit will return to the factory preset PIN number (000). All other user
programmed settings except the date and time will be retained.
Setting Emergency Phone Numbers
1.
Enter the PIN number and press the [PROG] button twice or until “MEMORY” flashes on the
LCD screen.
2.
Press the [ARM/DISARM] button to accept.
3.
Press the [#/DOWN] or [*/UP] button to select one of the number locations 1-5.
Note:
The 5 number locations represent the order in which the numbers will be dialed in the
case of an alarm.
4.
Enter the number to store including any area codes or dialing prefixes if needed (up to 32
digits, although only the last 16 digits can be shown on the LCD display) using the keypad
followed by the [ARM/DISARM] button to accept and store the number.
Note:
If needed, add a 4-second ‘pause’ before a PBX extension number by pressing and
holding the [DEL/PAUSE] button for 2 seconds until the letter ‘F’ appears on the LCD screen,
and then continuing with the extension number as usual. A ‘#’ or ‘*’ can also be entered by
pressing, and holding for two seconds, the [#/DOWN] or [*/UP] buttons respectively. The ‘#’
sign shows as ‘
┘
’ and the ‘*’ sign shows as ‘
└
’ on the LCD screen.
ENFORCER Auto Dialer
SECO-LARM U.S.A., Inc.
11
Operating the Auto Dialer, continued:
Remote Control by Telephone
The system can be remotely controlled and monitored through any Touch-Tone phone, including
mobile phones. The user may arm or disarm the system as well as listen in on the room.
1.
REMOTE CONTROL WHEN ALARM IS ACTIVATED
When an alarm has been activated and the auto dialer dials the pre-programmed emergency
numbers, the person who answers the call will hear a single “beep" for a sensor trigger or 4
“beeps” for panic button activation and may press one of the following function codes at any
time to control the system remotely:
Function
Press key code
Listen in
1 #
End call
3 #
Disarm system
6 #
The user should hear a “beep” in response. If not, enter the function code again.
2.
REMOTE CONTROL BY USER CALL-IN (CALL BACK)
A.
Using a mobile phone or any Touch-Tone phone, dial the phone number that the auto
dialer is connected to. The auto dialer will answer and “beep” once after the number of
rings in the pre-programmed call-in ringer detect cycle (3, 5, 7, or 10 rings, see pg. 8).
B.
Enter the PIN Number on the phone’s keypad. The dialer will “beep” twice if the correct
code has been entered. If a wrong code is entered, the dialer will disconnect automatically
and the user must dial in again.
C.
Press one of the following function codes to control the system remotely:
Function
Press key code
Listen in
1 #
Arm system
5 #
Disarm system
6 #
The user should hear a “beep” in response. If not, enter the function code again.
Note:
Should the user have difficulty activating functions remotely by telephone, there may
be too much ambient noise interference. Try pressing the code key again, or move to a
quieter location as ambient noise above 68dB may affect the auto dialer’s ability to detect the
tone signal.
3.
FUNCTION EXPLANATIONS
LISTEN IN – Pressing [1 #] allows a user to hear sound in the room for 50 seconds. A “beep”
will sound at 30 seconds to remind the user that the listen in time will soon end. Pressing [1 #]
again will reset the 50-second period, and entering any other key code will end monitoring and
perform the function. If there is no other key press, the call will disconnect at the end of the 50
seconds.
