Enerzone Destination 1.6 Installation And Operation Manual Download Page 11 | Manualshive

Page: 11 / 60

background image

Destination 1.6 Installation and Operation Manual

11

The C-Cast baffle is made of an aluminosilicate fibre material that is compressed with a binder to
form a rigid board. C-Cast can withstand temperatures above 2,000 °F. It is not considered
hazardous waste. Disposal at a landfill is recommended.

Firebrick is mainly composed of silicon dioxide, also known as silica, an earth derived product. It is
most commonly found in nature in the form of sand and clay. Disposal at a landfill is
recommended.

The door and glass gaskets are fibreglass which is spun from melted sand. Black gaskets have
been dipped into a solvent-free solution. Disposal at a landfill is recommended.

The  door  glass  is  a  5  mm  thick  ceramic  material  that  contains  no  toxic  chemicals.  It  is  basically
made of raw earth materials such as sand and quartz that are combined in such a way to form a
glass at high temperatures.  Ceramic glass will not re-melt in the same way as normal glass, so it
should  not  be  recycled  with  your  regular  household  products.  Disposal  at  a  landfill  is
recommended.

«
...
9
10
11
12
13
...
»

Summary of Contents for Destination 1.6





























































Reviews:

No comments

Related manuals for Destination 1.6

Brand: Mendip Stoves Pages: 13

Brand: Morso Pages: 24

OUTLAND LIVING FM2BS-210

Brand: FMI Pages: 16

Italiana Camini IDROPOLIS

Brand: EdilKamin Pages: 213

Tilefire KWF296-6068

Brand: KENT Pages: 2

Brand: Extraflame Pages: 40

Brand: chazelles Pages: 21

Brand: Magikal Pages: 31

THAMES TRAVEL BARGE 6910115

Brand: Clarke Pages: 24

Brand: Zempire Pages: 2

Brand: SCAN Pages: 16

Brand: SCAN Pages: 12

Brand: SCAN Pages: 28

Sonderskoven Inset 5

Brand: Cleanburn Pages: 16

Brand: Pevex Pages: 10

HSP 6 Premium 521.08

Brand: HAAS + SOHN Pages: 19

HSP 7 DIANA GRANDE RLU 451.08

Brand: HAAS + SOHN Pages: 23

Brand: Rsonic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands