Enerzone Destination 1.6 Installation And Operation Manual Download Page 4

Page: 4 / 60

Destination 1.6 Installation and Operation Manual

Maintaining Your Wood Heating System ............................... 23

5.1

Stove Maintenance ......................................................................................................... 23

5.1.1

Cleaning Door Glass .................................................................................................... 23

5.1.2

Door adjustment .......................................................................................................... 24

5.1.3

Replacing the Door Gasket .......................................................................................... 26

5.1.4

Replacing the Glass Gasket and/or the Glass .............................................................. 27

5.1.5

Cleaning and Painting the Stove .................................................................................. 29

5.2

Chimney and Chimney Connector Maintenance .............................................................. 29

5.2.1

Why Chimney Cleaning is Necessary .......................................................................... 29

5.2.2

How Often Should You Clean the Chimney? ............................................................... 30

5.2.3

Cleaning the Chimney ................................................................................................. 30

PART B - INSTALLATION ............................................................. 31

Safety Information ................................................................... 31

6.1

Summary of Installation Cautions and Warnings ............................................................. 31

6.2

Regulations Covering Stove Installation .......................................................................... 32

Clearances to Combustible Material ...................................... 33

7.1

Location of the certification label ..................................................................................... 33

7.2

Clearances to Walls and Ceiling ...................................................................................... 33

7.3

Floor protector ................................................................................................................. 36

7.4

Reducing Wall and Ceiling Clearances Safely ................................................................. 37

7.4.1

Shield Construction Rules ............................................................................................ 37

7.4.2

Table of Clearance Reduction Percentages ................................................................. 39

The Venting System ................................................................ 40

8.1

General ........................................................................................................................... 40

8.2

Suitable Chimneys .......................................................................................................... 40

8.2.1

Factory-built Metal Chimneys ...................................................................................... 40

8.2.2

Factory-built Metal Chimneys in mobile homes ............................................................ 41

8.2.3

Masonry Chimneys ...................................................................................................... 42

8.3

Minimum Chimney Height ............................................................................................... 42

8.4

The Relationship Between the Chimney and the House .................................................. 43

8.4.1

Why inside chimneys are preferred .............................................................................. 43

8.4.2

Why the chimney should penetrate the highest heated space ..................................... 44

8.5

Supply of Combustion Air ................................................................................................ 45

8.5.1

Combustion Air Supply in Mobile Homes ..................................................................... 45

8.5.2

Air Supply in Conventional Houses .............................................................................. 45

8.6

Installing the Chimney Connector .................................................................................... 46

8.6.1

Installation of Single Wall Chimney Connector ............................................................. 46

Summary of Contents for Destination 1.6





























































Search results

Summary of Contents for Destination 1.6

Reviews:

Related manuals for Destination 1.6

Brands by name

Popular brands

Enerzone Destination 1.6, Installation And Operation Manual

Search results

Summary of Contents for Destination 1.6

Reviews:

Related manuals for Destination 1.6

Brands by name

Popular brands