background image

7

C048-693-30 R02, Rev. B (04/2020)

4.2  

4.2  Mounting

Mounting

The HDX product can be mounted in a 19 in� or 23 in� rack 

configuration, in a front flush or mid-mount orientation.

 

Step 1. 

Attach the two (2) front mounting ears in the appropriate 

configuration using the included 1/4 in.-20 hardware as 

shown in Figure 1� 

4.3  

4.3  Chassis Ground

Chassis Ground

DO NOT ENERGIZE THE PANEL BEFORE CHASSIS 

GROUND IS CONNECTED�

CAUTION!

The chassis ground is located in the side of the panel (see Figure 

2)� A two hole lug landing position is provided� See table below for 

termination information screw is provided for attaching a chassis 

ground cable� A minimum of #4 AWG chassis ground cable is 

required for C016-452-10 model; a minimum of #2 AWG chassis 

ground cable is required for all other models�

IMPORTANT: Grounding hardware not included� A properly-sized 

grounding conductor must be installed per NEC (250�122)�

Table 2.  Ground Termination Summary

TWO HOLE 

LANDING 

TYPE

HOLE/

STUD SIZE

CENTER 

TO 

CENTER

RECOMMENDED 

TORQUE VALUE

Threaded Insert

1/4 in�-20

5/8 in�

90 in∙lbs

Step 1. 

Connect the lug to the chassis with 1/4 in�-20 hardware� Make 

sure heat shrink and no-oxide compound are applied 

appropriately prior to attachment�

Step 2. 

Torque the fasteners to 90 

in∙lbs

4.4  

4.4  Alarm Wiring

Alarm Wiring

On the rear of the panel, there is an 8p8c modular jack (RJ-45) for 

alarm connections� Plug a Cat 5/5e/6 UTP cable with a TIA/EIA 

T568B termination into the alarm jack� Refer to Table 3 below for 

alarm pin out� See drawings in Appendix A for the locations of these 

alarm connections for further detail� The following models feature an 

additional RJ-45 jack to allow for daisy chaining:

 

y

C016-450-10, C016-451-10

Table 3.  Alarm Contact Pin Out

┏━━ Major ━━┓

 

 

┏━━ Minor (Not Used) ━━┓

 

 

PIN 1

PIN 2

PIN 3

PIN 4

PIN 5

PIN 6

COM

N�C�

N�O�

COM

N�C�

N�O�

Figure 1.  Mounting Ears (19 in. shown)

Figure 2.  Chassis Ground Connection

Summary of Contents for alpha C016-450-10

























Reviews: