manualshive.com logo in svg

energy sentry 9212 Series 3, Owners & Installation Manual, Page: 29 / 34

Share
Download
energy sentry 9212 Series 3 Owners & Installation Manual Download Page 29

17.2.2

17.2.2

17.2.2

17.2.2

17.2.2

For the load schedule shown in Section 12.1.2, the
following system program is recommended:

System Program 2

Selected Load Control Strategy: 

 Fixed Priority.

System Configuration:

  Six relays installed.

Heating System: 

 Four circuits: heat pump with electric

forced air furnace, forced air furnace controls heat in     fixed
sequence. Hot water heater (#2) and dryer (#1) connected
to unit, 2 circuits.  Heat pump compressor           not
connected.

Electrical Service Size:

  40 KW.

Demand Averaging Period:

  30 minutes.

“Actual”

Display

“Limit”

Question

Answer

oL

Off-peak demand limit

oFF

nr

# of Relays

6

Pr1

Priority for Load #1

1

Pr2

Priority for Load #2

2

Pr3

Priority for Load #3

3

Pr4

Priority for Load #4

4

Pr5

Priority for Load #5

5

Pr6

Priority for Load #6

6

on1

Min. On Time Load #1

0

on2

Min. On Time Load #2

0

on3

Min. On Time Load #3

0

on4

Min. On Time Load #4

0

on5

Min. On Time Load #5

0

on6

Min. On Time Load #6

0

oF1

Min. Off Time Load #1

0

oF2

Min. Off Time Load #2

0

oF3

Min. Off Time Load #3

0

oF4

Min. Off Time Load #4

0

oF5

Min. Off Time Load #5

0

oF6

Min. Off Time Load #6

0

AP

Averaging Period

30

dr

Demand range

40

17.2.3

17.2.3

17.2.3

17.2.3

17.2.3

For the load schedule shown in 12.1.3, the following
program is recommended:

System Program 3

Selected Load Control Strategy:

  Fixed Priority.

System Configuration:

  Seven Relays installed.

Heating System:

  Five circuits: heat pump with electric

forced air furnace, forced air furnace controls heat in

27

17.2 Examples of

Programs

17.2.1

17.2.1

17.2.1

17.2.1

17.2.1

For the load schedule shown in Section 12.1.1 the
following system program is recommended:

System Program 1

Selected Load Control Strategy: 

 Fixed/Rotate Combi-

           nation.

System Configuration: 

 Eight relays installed.

Installed Heating System: 

 Six circuits, electric

baseboard or radiant ceiling; dryer (#1) and hot water
heater (#2), connected to unit, 2 circuits.

Electrical Service Size: 

 40 KW.

Averaging Period: 

 15 minutes.

___________________________________________

“Actual”

Display

“Limit”

Question

Answer

oL

Off-peak demand limit

oFF

nr

# of Relays

8

Pr1

Priority for Load #1

1

Pr2

Priority for Load #2

2

Pr3

Priority for Load #3

3

Pr4

Priority for Load #4

3

Pr5

Priority for Load #5

3

Pr6

Priority for Load #6

3

Pr7

Priority for Load #7

3

Pr8

Priority for Load #8

3

on1

Min. On Time Load #1

0

on2

Min. On Time Load #2

0

on3

Min. On Time Load #3

0

on4

Min. On Time Load #4

0

on5

Min. On Time Load #5

0

on6

Min. On Time Load #6

0

on7

Min. On Time Load #7

0

on8

Min. On Time Load #8

0

oF1

Min. Off Time Load #1

0

oF2

Min. Off Time Load #2

0

oF3

Min. Off Time Load #3

0

oF4

Min. Off Time Load #4

0

oF5

Min. Off Time Load #5

0

oF6

Min. Off Time Load #6

0

oF7

Min. Off Time Load #7

0

oF8

Min. Off Time Load #8

0

AP

—

Averaging Period

15

dr

—

Demand Range

40

Summary of Contents for 9212 Series 3



































Reviews:

No comments