R T M 3 2 0 5 U s e r M a n u a l
28
C H A P T E R T H R E E
29
R T M 3 2 0 5 U s e r M a n u a l
C O N T R O L A N D S T A T U S C O M M A N D S
inetdconfig
This command starts an interactive script that allows you to configure the list of protocol servers
which are started by the
inetd
super-server daemon running in RTM3205. Three protocol servers
may be configured: Time, Daytime, and Telnet. By default, the unit is configured to start all of these
protocol servers. If you need to disable start-up of some or all of these, e.g. for security reasons, you
must run this script as
root
from either the RS-232 serial I/O port or from a
telnet
or
ssh
session.
This script modifies the
/etc/inetd.conf
file, which is non-volatilely stored in the FLASH disk
/boot/
etc
directory. You must reboot RTM3205 after running this script for the changes to take effect.
Command:
inetdconfig
RTM3205 reply: Interactive script is started.
inhibitoutputsmode
This command shows the current inhibit mode of the timing signal outputs (if any) prior to initial
system lock to the GPS receiver. If it is set to ON, then all timing signals will be inhibited (not pres-
ent) until the system is locked to the timing receiver. If it is set to OFF, then the timing signals will
be present at all times.
Command:
inhibitoutputsmode
RTM3205 reply:
OFF
installed_sw_opts
See
Appendix I - Software Options
for information on this command.
ionostat (Optional)
This command is only available if the RTIC option has been installed. Refer to
Chapter 11 - Real-
Time Ionospheric Corrections
for more information.
kernelversion
This command prints the current Linux operating system kernel firmware version.
Command:
kernelversion
RTM3205 reply:
6010-0064-000_v1.00 Linux Kernel 3.2.2-Sonoma #2 Dec 19 01:08:43 2012
logrinex
This command is used to control logging of raw GPS pseudorange and carrier phase observations in
the Rinex version 2.11 format to the
/home/rinex/rinex.log
file. It requires one argument, which may
be either ON or OFF.
If ON is asserted and logging is not currently in progress, then a new log of 2880 observations taken
every 30 seconds will begin. Assuming full constellation visibility, this will take 24 hours to com-
plete. If a previously-initiated log is in progress, then an ON assertion will be ignored.
Summary of Contents for RTM3205
