Endress+Hauser MODBUS RS485 Operating Instructions Manual Download Page 25

Page: 25 / 92

LPGmass Modbus RS485

Electrical connection

Hauser

Safety Barrier Promass 100

Safe area

L+

Power
supply
24V

Modbus

RS485

L+

Power
supply

Modbus

RS485

Hazardous area

Safety Barrier
Promass 100

Power

Communication

Lift panel for
bus termination

A0030220

 7

Safety Barrier Promass 100 with terminals

Non-hazardous area and Zone 2/Div. 2

Intrinsically safe area

7.1.4

Preparing the measuring device

NOTICE

Insufficient sealing of the housing!

Operational reliability of the measuring device could be compromised.

‣

Use suitable cable glands corresponding to the degree of protection.

1. Remove dummy plug if present.
2. If the measuring device is supplied without cable glands:

Provide suitable cable gland for corresponding connecting cable.

3. If the measuring device is supplied with cable glands:

Observe requirements for connecting cables →  22.

7.2

Connecting the measuring device

NOTICE

Limitation of electrical safety due to incorrect connection!

‣

Have electrical connection work carried out by correspondingly trained specialists only.

‣

Observe applicable federal/national installation codes and regulations.

‣

Comply with local workplace safety regulations.

‣

Always connect the protective ground cable before connecting additional cables.

‣

For use in potentially explosive atmospheres, observe the information in the device-

specific Ex documentation.

‣

The power unit must be tested to ensure it meets safety requirements (e.g. PELV,

SELV).

Summary of Contents for MODBUS RS485





























































































Search results

Summary of Contents for MODBUS RS485

Reviews:

Related manuals for MODBUS RS485

Brands by name

Popular brands

Endress+Hauser MODBUS RS485, Operating Instructions Manual

Search results

Summary of Contents for MODBUS RS485

Reviews:

Related manuals for MODBUS RS485

Brands by name

Popular brands