Endress+Hauser MODBUS RS485 Operating Instructions Manual Download Page 11

Page: 11 / 92

LPGmass Modbus RS485

Product description

Hauser

Product description

The device consists of a transmitter and a sensor. If a device is ordered with Modbus

RS485 intrinsically safe, the Safety Barrier Promass 100 is part of the scope of supply and

must be implemented to operate the device.
One device version is available: compact version, transmitter and sensor form a mechanical

unit.

3.1

Product design

3.1.1

Device version with Modbus RS485 communication type

A0017609

 1

Important components of a measuring device

Sensor

Transmitter housing

Main electronics module

Transmitter housing cover

In the case of the device version with Modbus RS485 intrinsically safe, the Safety

Barrier Promass 100 forms part of the scope of supply.

Summary of Contents for MODBUS RS485





























































































Search results

Summary of Contents for MODBUS RS485

Reviews:

Related manuals for MODBUS RS485

Brands by name

Popular brands

Endress+Hauser MODBUS RS485, Operating Instructions Manual

Search results

Summary of Contents for MODBUS RS485

Reviews:

Related manuals for MODBUS RS485

Brands by name

Popular brands