Endress+Hauser Flowfit CYA27 Operating Instructions Manual Download Page 43

Page: 43 / 52

Flowfit CYA27

Accessories

Hauser

Accessories

The following are the most important accessories available at the time this documentation

was issued.

‣

For accessories not listed here, please contact your Service or Sales Center.

11.1 Device-specific accessories

11.1.1 Disinfection sensors

CCS51D

• Sensor for measuring free chlorine

• With Memosens technology

• Product Configurator on the product page:

www.endress.com/ccs51d

Technical Information TI01423C

CCS50D

• Membrane-covered amperometric sensor for chlorine dioxide

• With Memosens technology

• Product Configurator on the product page:

www.endress.com/ccs50d

Technical Information TI01353C

CCS55D

• Sensor for measuring free bromine

• With Memosens technology

• Product Configurator on the product page:

www.endress.com/ccs55d

Technical Information TI01423C

11.1.2 pH sensors

Memosens CPS31D

• pH electrode with gel-filled reference system with ceramic diaphragm

• Product Configurator on the product page:

www.endress.com/cps31d

Technical Information TI00030C

Orbisint CPS11D / CPS11

• pH sensor for process technology

• With dirt-repellent PTFE diaphragm

• Product Configurator on the product page:

www.endress.com/cps11d

www.endress.com/cps11

Technical Information TI00028C

Ceraliquid CPS41D / CPS41

• pH electrode with ceramic junction and KCl liquid electrolyte

• Product Configurator on the product page:

www.endress.com/cps41d

www.endress.com/cps41

Technical Information TI00079C

Summary of Contents for Flowfit CYA27





















































Search results

Summary of Contents for Flowfit CYA27

Reviews:

Related manuals for Flowfit CYA27

Brands by name

Popular brands

Endress+Hauser Flowfit CYA27, Operating Instructions Manual

Search results

Summary of Contents for Flowfit CYA27

Reviews:

Related manuals for Flowfit CYA27

Brands by name

Popular brands