Encore 52K23A Prowler Mid-Cut Operator'S Manual Download Page 2

1

SIGNAL WORDS

This symbol means

 “Attention! Become

Alert! Your Safety is Involved!” 

The symbol

is used with the following signal action words
to attract your attention to safety messages.
The message that follows the symbol con-
tains important information about safety.

Signal Word:

 

WARNING:

The signal action word “ WARNING” denotes
that a hazard exists on or near the machine
that can result in injury or death if proper
precautions are not taken.

 

CAUTION:

The signal action word “CAUTION” is a re-
minder of safety practices on or near the
machine that could result in personal injury if
proper precautions are not taken.

NOTES:

The signal action word “NOTES” denotes
relevant information to assist you in the perfor-
mance of a task.

GENERAL

This manual contains techincal data on the
following  Encore commercial mowers.

52K650ZP ; 52K700ZP ; 52K850ZP ; 61K650P
61B850P ; 61B950P ; 61K650ZP ; 61K700ZP
61K850ZP ; 61B850ZP ; 72B850P ; 72B950P
72B850ZP ; 72K850ZP -- 52K23A ; 52K25A 52K27L ;
61K27L; 51B27LD ; 61K25A ; 61B31LP  72K27L ;
72B27LD ; 72B31LP

INTRODUCTION

Your mower was built to the highest standards in
the industry. However, the prolonged life and
maximum efficiency of your mower depends on
you following the operating, maintenance and
adjustment instructions in this manual.

We encourage you to contact your local Encore
dealer for repairs. All Encore dealers are
informed of the latest methods to service this
equipment and provide prompt and efficient
service. They carry a full line of Encore service
parts.

A replacement Operator’s Manual is available
from your Encore Dealer or by contacting
Encore Manufacturing Co., Inc., Service
Department at PO Box 888, Beatrice, NE
68310. Please indicate the complete model
and serial number of your Encore product.

The “Right” and “Left”,”Front” and “Rear” of the
machine are referenced from the operator’s
perspective when in the normal operating
position and facing forward travel direction.

GENERAL SAFETY INSTRUCTIONS

READ THIS OPERATOR’S MANUAL

 and

instructions furnished with attachments.
Perform only those maintenance procedures
described in this manual. If major repairs are
ever needed or assistance is desired, contact

an Authorized Encore Dealer. To ensure
optimum performance and safety, always
purchase genuine Encore replacement parts
and accessories

Summary of Contents for 52K23A Prowler Mid-Cut

















Reviews: