EMS Sky Connect Series Page 62 Installation Manual Download

Page: 62 / 70

NOTES:

Connect 22AWG spliced as shown to 18AWG.

Optional "LINK" light may be used to indicate unit failure if light is illuminated. Check software options.

All audio wires are twisted pairs. Shield floats at one end.

All unused pins are reserved, DO NOT connect anything to reserved pins.

All wire numbers are examples. Use what suits your installation.

PC connector may be used for upgrades and PC data calls. Avoid long RS232 runs in noisy environments.

This port is NOT to be used for diagnostics connections of PC.

See installation instructions on Coax. type, typically RG400.

GPS antenna used in installations if GPS sensor installed in transceiver.

Configuration module is optional.

12. Wire dimmer to 5-28VDC or through 1 amp breaker in absence of dimmer buss.

14. Squat/Collective/WOW switch is strongly recommended for helicopter, but optional for fixed wing A/C. Units

with 4.5 or higher version of software may Depart and Arrive on GPS data changing.

19. If configuration module is installed these wires must not be more than 8" long.

21. Mount in remote location for easy access. Connect PC serial cable for unit configuration.

23. Lighting for Dialer is selected on the appropriate pins. When dimmer is turned off, lights will go to full

brightness.

24. Pin 1 is back lighting, Pin 9 is power to the annunciators. Separate if needed. Use two stage dimming if

needed to annunciators.

Revision History

Rev

Date

Description

1.1

4/12/05

Added Note 22

1.2

7/1/05

Changed note 6 and 17

1.3

7/11/05

Expanded Parts List added #23

1.4

1/18/07

Added Note 24

1.5

8/31/07

Revised note #14

1.6

9/19/07

Revised notes, removed obsolete notes for A Model

2.0

8/16/11

Eliminated obsolete notes. Created complete parts list.

PARTS LIST AND NOTES

(1616-910-01)

MS25041-x

ANNUNCIATOR

DIALIGHT

MS26574-3

CIRCUIT BREAKER, 3 AMP

KLIXON

MS26574-2

CIRCUIT BREAKER, 2 AMP

KLIXON

1616-721-04

(M39029/64-369)

CONTACT, 20G MALE

SKY CONNECT
(CINCH)

1616-721-02

(M39029/63-368)

CONTACT, 20G FEMALE

SKY CONNECT
(CINCH)

D20419

MALE SCREWLOCK KIT

CANNON

D20418

FEMALE SCREWLOCK KIT

CANNON

1616-722-04

(DE-24657)

HOOD 9

SKY CONNECT
(CINCH)

1616-722-01

(DA-24658)

HOOD 15

SKY CONNECT
(CINCH)

1616-722-02

(DB-24659)

HOOD 25

SKY CONNECT
(CINCH)

1616-725-25

(D25000JVL0)

HOOD 25 WITH VIBRATION LOCK

SKY CONNECT
(POSITRONICS)

1616-720-01

(M24308/2-2F)

D-SUB CONNECTOR, 15 F

SKY CONNECT
(CINCH)

1616-720-04

(M24308/2-1F)

D-SUB CONNECTOR, 9 F

SKY CONNECT
(CINCH)

1616-720-05

(M24308/4-1F)

D-SUB CONNECTOR, 9 M

SKY CONNECT
(CINCH)

1616-720-02

(M24308/2-3F)

D-SUB CONNECTOR, 25 F

SKY CONNECT
(CINCH)

1616-105-02

(DD62F10Z00)

D-SUB CONN KIT, 62 F HD

SKY CONNECT
(POSITRONICS)

N/A

COAX CABLE, RG400 OR EQ.

BELDEN

031-4427

CONNECTOR, BNC

AMPHENOL

031-4452

CONNECTOR, TNC

AMPHENOL

1 (OPT)

1616-880-04

(S67-1575-39)

GPS ANTENNA

SKY CONNECT
(SENSOR SYSTEMS)

1 (STD)

1616-880-01

(AT2775-110GAO-TNCF)

IRIDIUM ANTENNA

SKY CONNECT
(AERO ANTENNA)

1 (OPT)

1616-880-13

(L10-806)

IRIDIUM/GPS ANTENNA

SKY CONNECT
(DAYTON-GRANGER)

1616-880-13

(5G1516RR-AP-XTT-1)

SKY CONNECT
(ANTCOM)

1 (OPT)

1616-905-02

CONFIGURATION MODULE

SKY CONNECT

1 (STD)

1616-052-00

SOP 11 DIALER

SKY CONNECT

1 (OPT)

1616-052-02

SOP 11 DIALER, NVIS

SKY CONNECT

1 (OPT)

1616-055-11

MMU II, NVIS

SKY CONNECT

1 (STD)

1616-055-13

MMU II

SKY CONNECT

1616-105-01

MOUNTING TRAY

SKY CONNECT

1 (OPT)

1616-050-05A

TRANSCEIVER, AFF

SKY CONNECT

1 (OPT)

1616-050-04A

TRANSCEIVER, 4 WIRE, NO GPS

SKY CONNECT

1 (STD)

1616-050-03A

TRANSCEIVER, 4 WIRE

SKY CONNECT

1 (OPT)

1616-050-02A

TRANSCEIVER, NO AUDIO, NO GPS SKY CONNECT

1 (OPT)

1616-050-01A

TRANSCEIVER, NO AUDIO

SKY CONNECT

-15

-11

-02

ITEM

PART NUMBER

DESCRIPTION

SUPPLIER

PARTS LIST

Michael Freyder

01/31/2005

Christopher Malpass

08/16/2011

Michael Freyder

08/16/2011

1616-910.dwg

Sky Connect Tracker Installation

1616-910

1 of 4

N/A

2.0

Drawn

Revised

Checked / Approved

Filename

Size

Sheet

Scale

Rev

Drawing Number

All dimensions are in inches unless
otherwise specified.

Dimensions marked:

[X.XX] REF

are existing geometry,

and are supplied as reference only.

[X.XX] TYP

are typical dimensions

are are supplied as reference only

Tolerances, unless otherwise
specified:

x.x ± .05"
x.xx ± .01"
x.xxx ± .005"
x° ± 2°

This data is provided as a CONFIDENTIAL and PRIVILEGED DOCUMENT by EMS Aviation. Any other use or

reproduction without the expressed written consent of EMS Aviation is expressly forbidden. Any misuse of this
document including (but not limited to) quotation in part without written consent of EMS Aviation is expressly forbidden.

DER Review

Summary of Contents for Sky Connect Series







































































Search results

Summary of Contents for Sky Connect Series

Reviews:

Related manuals for Sky Connect Series

Brands by name

Popular brands

EMS Sky Connect Series, Installation Manual

Search results

Summary of Contents for Sky Connect Series

Reviews:

Related manuals for Sky Connect Series

Brands by name

Popular brands