EMS Sky Connect Series Page 5 Installation Manual Download

Page: 5 / 70

1616-964-12

Date: 7/27/2011

Rev. 2.1

LIST OF REVISIONS

Revision #

Description of Change

Date

Approval

1.0

Removed all POTS unit information and
created a new manual part number for
Tracker only.

3/24/2007

MLF

1.1

Added Combo antenna, corrected note on
ICSM, revised pin out chart to remove the
400 series references.

3/20/2008

MLF

1.2

Typos corrected, revised MMU/MMU II
recommended installation wiring
drawing

10/3/2008

MLF

1.3

Added spec and part numbers for MMU II

12/15/2008

MLF

1.4

Added configuration details on MMU II
and Combo antenna drawing

1/13/2009

MLF

1.5

Revised to indicate the changes to the
1616-105-01 tray per ECO 10013

6/3/2010

MLF

2.0

Revised to add description of MMU II
features for Wi-Fi MSet Loads and
Performing Tracker Setup through the
MMU II, Added MMU II Master/Slave
Configuration

4/7/2011

MLF

2.1

Revised Annuc. #2 description, includes a
picture of the SOP 11 jumper

7/27/2011

MLF

Summary of Contents for Sky Connect Series







































































Search results

Summary of Contents for Sky Connect Series

Reviews:

Related manuals for Sky Connect Series

Brands by name

Popular brands

EMS Sky Connect Series, Installation Manual

Search results

Summary of Contents for Sky Connect Series

Reviews:

Related manuals for Sky Connect Series

Brands by name

Popular brands