background image

EMS SYSTEM 7000 

 

©2015 EMS Security Group Ltd. All rights reserved.                     TSD248 Iss 2 25/06/15 AJM

 

28 

17.11

 

By using the “4” button to move left or the “6” button to move right, move to the 
letter or number required and press the “5” button to select the character. 

 
17.12

 

Repeat 16.11 until all letters have been selected. Once completed, Press the “

” 

button to save the information. 

 
17.13

 

Once completed you may now escape from this menu by pressing the “3” button 
on  the  keypad  until  the  “SYSTEM  RESET”  message  appears  or  by  returning  the 
control keyswitch to the “CLEAR

” 

position. 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

KEY                                                       FUNCTION 

Enters a blank space into the new device name being entered. 

Exits to the previous menu 

Moves the alphabet wheel of characters to the 

Left

, by one character space at a 

time. 

Enters the character in the 

centre

 directly above the character 

selector |.

 

Moves the alphabet wheel of characters to the

 Right

, by one character space at a 

time. 

Moves  the  flashing  cursor  to  the 

left

,  through  the  new  device  name  by  one 

character space at a time. 

Moves the alphabet wheel of characters to the

 Right

, by 12 character Spaces at a 

time. 

Moves  the  flashing  cursor  to  the 

Right

,  through  the  new  device  name  by  one 

character space at a time. 

 

Backspace Key, 

Deletes 

by one character. (Deletes to the left only) 

 

Saves  and  completes  the  current  activity  and  returns  the  program  to  the 

appropriate display. 

Summary of Contents for 7256





























Reviews: