background image

 
 

 

Single Phase Motor Energy Control - Page 9 of 20 

 

3.10 INPUT/OUTPUT CONTROL CONNECTIONS 

To avoid 'interference pick up' all input and output control cables should be kept as short as 
possible and should wherever possible, be shielded. If noise free lines cannot be 
guaranteed, an interposing relay with suitable suppression must be used, this should be 
mounted as close to the 

EnviroStart

 as possible. 

 

3.11 EMISSIONS 

EnviroStart

 units produce relatively low Radio Frequency Interference (RFI) compared with 

frequency inverters and no external filters are required in normal circumstances. (See also 
Section 3.3 – Harmonics). 

 

 3.12 CABLE AND INPUT FUSE RATINGS 

Incoming fuses and power cables should generally comply with the ratings as shown in the 
table below. It is recommended that all cable be tri-rated compliant with BS 6231 and that all 
fuses be motor rated, bolt fitting, compliant with BS 88 Part 2. (It is not necessary to use 
motor rated fuses if the unit is being used in DPR Mode).  

 

MODEL 

FUSE 

RATING 

CABLE 

RATING 

 

MODEL 

FUSE 

RATING 

CABLE 

RATING 

110-SPMECG6-4A 

5A 

14A/0.75mm/20AWG 

 

220-SPMECG6-4A 

5A 

14A/0.75mm/20AWG 

110-SPMECG6-10A 

10A 

14A/1.5mm/18AWG 

 

220-SPMECG6-10A 

10A 

14A/1.5mm/18AWG 

110-SPMECG6-25A 

25A 

14A/2.5mm/14AWG 

 

220-SPMECG6-25A 

25A 

14A/2.5mm/14AWG 

110-SPMECG6-4A/60 

5A 

14A/0.75mm/20AWG 

 

220-SPMECG6-4A/60 

5A 

14A/0.75mm/20AWG 

110-SPMECG6-10A/60 

10A 

14A/1.5mm/18AWG 

 

220-SPMECG6-10A/60 

10A 

14A/1.5mm/18AWG 

110-SPMECG6-25A/60 

25A 

14A/2.5mm/14AWG 

 

220-SPMECG6-25A/60 

25A 

14A/2.5mm/14AWG 

The above detail refers to new installations, where the 

EnviroStart

 is fitted into an existing 

installation; cable should be rated according to the fuses already fitted.   

 

 

 

 

 

 

 

 

Summary of Contents for 110-SPMECG6-10A





















Reviews: