background image

Page 1

INSTALLATION INSTRUCTIONS

AND

OWNER'S MANUAL

FAN TYPE

DIRECT  VENT 

WALL  FURNACE

For Installation in 

Manufactured (Mobile Home), 

Modular or Residential Homes

MODEL

DV-55E-5

WARNING:  If  not  installed,  operated  and 
maintained in accordance with the manufactur-
er's instructions, this product could expose you 
to substances in fuel or from fuel combustion 
which can cause death or serious illness.

Patent # 5.664.555

This  appliance  may  be  installed  as  an  OEM 
installation in a manufactured home (USA only) 
or mobile home and must be installed in ac-
cordance with the manufacturer's instructions 
and the Manufactured Home Construction and 
Safety Standard, Title 24 CFR, Part 3280, in the 
United States, or the Mobile Home Standard, 
CAN/CSA Z240 MH Series, in Canada.

This appliance is only for use with the type(s) 
of gas indicated on the rating plate. A conver-
sion kit is supplied with the appliance.

Installer:  Leave this manual with the appli-

ance.

Consumer: Retain this manual for future refer-

ence.

—  Do not store or use gasoline or other flamma-

ble vapors and liquids in the vicinity of this or 
any other appliance.

—  WHAT TO DO IF YOU SMELL GAS
 

• 

Do not try to light any appliance.

 

• 

Do not touch any electrical switch; do not 
use any phone in your building.

 

• 

Immediately call your gas supplier from a 
neighbor’s  phone.  Follow  the  gas  suppli-
er’s instructions.

 

• 

If you cannot reach your gas supplier, call 
the fire department.

—  Installation and service must be performed by 

a qualified installer, service agency or the gas 
supplier.

WARNING: If the information in these instruc-
tions are not followed exactly, a fire or explosion 
may result causing property damage, personal 
injury or loss of life.

 ACF Greenhouses 

Summary of Contents for DV-55E





















Reviews: