28091-8-0814
Page 27
VFXI AND VFNI REMOTE CONTROL INSTRUCTIONS
SETTING THE TEMPERATURE
• Select either the
TEMP
MODE or the
TEMP
MODE by
briefly pressing the SET button.
•
Hold the
SET
button until the TEMP display flashes.
•
Set the desired temperature with
(large flame) or
(small
flame).
• Press
OFF
or simply wait to complete programming.
•
Notice:
When the desired room temperature is SET on the
hand held remote, the burner will automatically turn on when
the room temperature drops 3 degrees Fahrenheit (F) below
the SET temperature. The remote system will turn the burner
off when the room temperature reaches 3 degrees Fahren-
heit (F) above the SET temperature. The pilot will remain lit
between burner cycles when using the thermostatic remote
control feature.
Default Settings
Program 1:
P1 :6:00am P1
:8:00am
Program 2:
P2 :11:50pm P2
:11:50pm
•
2 ON times can be programmed per day.
•
The day starts at 12:00am, ends at 11:50pm
•
The ON/OFF times have to be programmed in the order
P1
≤ P1
< P2
≤
.
•
If P1 = P1 or P2 = P2 the timer is deactivated.
•
To have the fire over night, it can be set:
P2 11:50am and P1 12:00am
•
Select Timer Mode by briefly pressing the
SET
button.
6 Hour no Communication Function
•
Manual Mode/Temperature/Timer Mode: The valve will turn to
pilot flame if there is no change in flame height for a 6 hour
period. In Termperature/Timer Mode, if the ambient room tem-
perature changes, the flame height willa djust automatically to
maintain set temperature, and the fire will continue to function
normally. The valve will turn to pilot flame if the set tempera
-
ture and the ambient room temperature remain the same over
a 6 hour period.
Five Day Shut Off
•
The system shuts off the fire completely if there is no change
in the flame height for 5 days.
NOTE:
Before the next ignition there is a 2 minute waiting period.
MANUAL OPERATION
Follow appliance lighting instructions for gaining access to the gas
control and the pilot burner. Access to the pilot burner is only re-
quired for ignition with a match.
When turning main valve knob, do not force. Knob has a slip clutch
that clicks until the end stops are reached. This allows for manual
flame height adjustment as well as adjustment to pilot standby po
-
sition.
1.
STOP!
Read the safety information included before proceed-
ing.
2. Turn main valve knob to the
OFF
, full clockwise
position.
3. Turn MANUAL knob to the
MAN
, full clockwise
position.
4. Place ON/OFF switch (if equipped) in
O
(OFF position).
SETTING THE TIME
Display, Timer/Thermostat RF Remote Handsets
•
The display will flash after either:
a. Installing the battery or
b. Simultaneously pressing the
(large flame) and
(small
flame)
•
Press
(large flame) to set the hour and the (small flame)
to set the minute.
•
Press OFF to return to manual mode or simply wait and it will
automatically return to the manual mode.
CHANGING THE MODE OF OPERATION
Briefly pressing the
SET
button changes the mode of operation in
the following order:
Notice
: MANUAL mode can also be reached by pressing either
the
(large flame) or the (small flame).
and back to
MAN
Mode - Manual Flame Height Adjustment
• Press
(large flame) to turn on the main burner.
•
Press
(large flame) to increase the flame height.
• Press
(small flame) to decrease the flame height or to go to
pilot standby position.
Notice:
While pressing either button a symbol indicating trans-
mission appears on the display. The receiver confirms
transmission with a beep.
TEMP
- Daytime Temperature Mode
(appliance must be in standby mode; pilot ignited): The room tem-
perature is measured and compared to the set temperature. The
flame height is then automatically adjusted to achieve the Daytime
set temperature.
TEMP
- Nighttime Setback Temperature Mode
(appliance must be in standby mode; pilot ignited):
The room temperature is measured and compared to the Night-
time Setback temperature. The flame height is then automatically
adjusted to achieve the Nighttime Setback temperature.
TIMER
- Timer Mode
Setting P1 ON time
•
Hold the
SET
button until P1 (sun) is displayed and the
time flashes.
•
Set the hour by pressing the
(large flame) button.
•
Set the inutes by pressing the
(small flame) button.
Setting P1 OFF time
•
Briefly press
SET
button to scroll to setting P1 OFF time. P1
(moon) is displayed at the time flashes.
•
Set the hour by pressing the
(large flame) button.
•
Set the inutes by pressing the
(small flame) button.
MAN
TEMP
TEMP
TIMER
MAN
