background image

Page 1

20248-2-0806

INSTALLATION INSTRUCTIONS

AND

OWNER'S MANUAL

UNVENTED 

GAS FIREPLACE

MODELS

VF24FP2-1 

VF24FP3-1

EFFECTIVE  DATE 

AUGUST 2006

The 

Vail

 Vent-Free Gas Fireplaces

This appliance may be installed in an aftermar-

ket, permanently located, manufactured (mobile) 

home, where not prohibited by local codes.
This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is not 

convertible for use with other gases.

This  is  an  unvented  gas-fired  heater.  It  uses  air 

(oxygen)  from  the  room  in  which  it  is  installed. 

Provisions for adequate combustion and ventila-

tion air must be provided. Refer to page 6.

WATER  VAPOR:  A  BY-PRODUCT  OF 

UNVENTED ROOM HEATERS

Water vapor is a by-product of gas combustion. 

An unvented room heater produces approximate-

ly one (1) ounce (30ml) of water for every 1,000 

BTU's  (.3KW's)  of  gas  input  per  hour.  Refer  to 

page 6.

WARNING: If not installed, operated and main-

tained in accordance with the manufacturer's in-

structions, this product could expose you to sub-

stances in fuel or from fuel combustion which can 

cause death or serious illness.

—  Do not store or use gasoline or other flamma-

ble vapors and liquids in the vicinity of this or 

any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

  •  Do not try to light any appliance.

  •  Do not touch any electrical switch; do not 

use any phone in your building.

  •  Immediately call your gas supplier from a 

neighbor’s  phone.  Follow  the  gas  suppli-

er’s instructions.

  •  If you cannot reach your gas supplier, call 

the fire department.

—  Installation and service must be performed by 

a qualified installer, service agency or the gas 

supplier.

WARNING: If the information in these instruc-

tions are not followed exactly, a fire or explosion 

may result causing property damage, personal 

injury or loss of life.

Installer:  Leave this manual with the appli-

ance.

Consumer: Retain this manual for future refer-

ence.

Summary of Contents for VF24FP2-1





























Reviews: