background image

1

W415-0318 / 03.05.09

$10.00

INSTALLATION 

AND 

OPERATING 

INSTRUCTIONS

If the information in these instructions are 
not followed exactly, a fire or explosion 
may result causing property damage, 
personal injury or loss of life.

- Do not store or use gasoline or other 
flammable vapors and liquids in the vicinity 
of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:
  Do not try to light any appliance.
  Do not touch any electrical switch; do  
  not use any phone in your building.
  Immediately call your gas supplier from  
  a neighbour’s phone.  Follow the gas  
 supplier’s 

instructions.

  If you cannot reach your gas supplier,  
  call the fire department.
- Installation and service must be 
performed by a qualified installer, service 
agency or the supplier.

SAFETY INFORMATION

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.

!

WARNING

INSTALLER:  LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER:  RETAIN THIS MANUAL FOR FUTURE REFERENCE.

APPLY SERIAL NUMBER LABEL FROM CARTON

Serial No.

MODEL NO.

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 4Y8 Canada / 

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.continentalfireplaces.com • [email protected]

1.9

CDI-44N

NATURAL GAS

CDI-44P

PROPANE

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.33, ANSI Z21.88 FOR VENTED GAS FIREPLACE HEATERS.

Summary of Contents for CDI-44N





























Reviews: