background image

25700-1-0809

Page 3

IMPORTANT SAFETY INFORMATION

THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.

•  Due  to  high  temperatures  the  appliance  should  be 

 

located  out  of  traffic  and  away  from  furniture  and 

 

draperies.

•  Children  and  adults  should  be  alerted  to  the  hazards 

of high surface temperatures and should stay away to 

avoid burns or clothing ignition.

•  Young  children  should  be  carefully  supervised  when 

they are in the same room as the appliance. Toddlers, 

young children and others may be susceptible to acci-

dental contact burns. A physical barrier is recommend-

ed if there are at risk individuals in the house. To restrict 

access to a fireplace or stove, install an adjustale safety 

gate  to  keep  away  toddlers,  young  children  and  other 

at risk individuals out of the room and away from hot 

surfaces.

•  Clothing  or  other  flammable  material  should  not  be 

placed on or near the appliance.

•  Any  safety  screen  or  guard  removed  for  servicing  an 

 

appliance  must  be  replaced  prior  to  operating  the  

appliance.

•  Keep burner and control compartment clean.
•  Vent cap hot while furnace is in operation.
•  For  manufactured  home  (USA  only)  or  mobile  home 

or  residential  installation  convertible  for  use  with  

natural  gas  and  liquefied  petroleum  gases  when 

 

provision  is  made  for  the  simple  conversion  from  one 

gas to the other.

•  Installation  and  repair  should  be  done  by  a 

 

QUALIFIED  SERVICE  PERSON.  The  appliance 

should  be  inspected  before  use  and  at  least  annually 

by  a  qualified  service  person.  More  frequent  cleaning 

may  be  required  due  to  excessive  lint  from  carpeting,  

bedding  materials,  etc.  It  is  imperative  that  control  

compartments, burners and circulating air passageways 

of the appliance be kept clean.

•  DO  NOT  put  anything  around  the  furnace  that  will 

 

obstruct the flow of combustion and ventilation air.

•  DO  keep  the  appliance  area  clear  and  free  from 

 

combustible  material,  gasoline  and  other  flammable 

 

vapors and liquids.

•  Do  examine  venting  system  periodically  and  replace 

damaged parts.

•  Do make a periodic visual check of burner. Clean and 

replace damaged parts.

•  DO  NOT  use  this  heater  if  any  part  has  been  under 

 

water.  Immediately  call  a  qualified  service  technician 

to  inspect  the  heater  and  to  replace  any  part  of  the  

control  system  and  any  gas  control  which  has  been  

under water.

Summary of Contents for Mantis FF28BMN-1

























































Reviews: