![background image](http://html1.mh-extra.com/html/empire-comfort-systems/dvp36fp30n-5/dvp36fp30n-5_installation-instructions-and-owners-manual_2404095047.webp)
39358-3-1019
Page 47
to tURN oFF GAS to FIRePLACe
FoR YoUR SAFetY ReAD BeFoRe LIGHtING
A. This appliance has a pilot which must be lighted by hand. When
lighting the pilot, follow these instructions exactly.
B. Before lighting smell all around the appliance area for gas. Be
sure to smell next to the floor because some gas is heavier
than air and will settle on the floor.
What To Do If You Smell Gas
• Do not try to light any appliance.
• Do not touch any electrical switch;
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it; call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
LIGHtING INStRUCtIoNS
1. Set REMOTE/OFF/ON switch to OFF.
2. Turn off all electric power to the appliance if service is to be
performed (if applicable).
3. Lower bottom louver assembly.
4. Push in gas control knob slightly and turn clockwise
to "OFF." Do not force.
5. Close bottom louver assembly.
1. Stop! Read the safety information above.
2. Set REMOTE/OFF/ON switch to OFF.
3. Turn off all electric power to the appliance (if applicable).
4. Lower bottom louver assembly.
5. Push in gas control knob slightly and turn clockwise
to "OFF."
Note: Knob cannot be turned from "PILOT" to "OFF" unless knob is
pushed in slightly. Do not force.
6. Wait ten minutes to clear out any gas. Then smell for gas, including
near the floor. If you then smell gas, STOP! Follow "B" in the safety
information above. If you do not smell gas, go to the next step.
7. Find pilot - Follow metal tube from gas control. The pilot is behind the
burner on the right side.
8. Turn gas control knob counterclockwise
to "PILOT."
9. Push in control knob all the way and hold in. Repeatedly push the piezo
ignitor button until the pilot is lit. Continue to hold the control knob in the
for about one minute after the pilot is lit. Release knob, and it will pop
back up. Pilot should remain lit. If it goes out, repeat steps 5 through
9.
•
If the control knob does not pop up when released, STOP and
IMMEDIATELY call a qualified service technician or gas supplier.
•
If the pilot will not stay lit after several tries, turn the gas control
knob to "OFF" and call your service technician or gas supplier.
10. Turn gas control knob counterclockwise
to "ON."
11. Close bottom louver assembly.
12. Turn on all electric power to the appliance (if applicable).
13. Set REMOTE/OFF/ON switch to desired setting.
MILLIVoLt SYSteM StANDING PILot LIGHtING INStRUCtIoNS
WARNING
If you do not follow these instructions exactly, a fire or explosion may result causing property damage,
personal injury, or loss of life.
Summary of Contents for DVP36FP30N-5
Page 20: ...39358 3 1019 Page 20 Figure 29 Figure 30 Figure 31 EXAMPLES TOP VENT RUN...
Page 37: ...39358 3 1019 Page 37 Figure 57 DVVK 4FV DIRECT VENT TERMINATION KIT CONT D...
Page 46: ...39358 3 1019 Page 46 Figure 70 MILLIVOLT SYSTEM STANDING PILOT WIRING DIAGRAM...