![background image](http://html1.mh-extra.com/html/empire-comfort-systems/dvp36fp30n-5/dvp36fp30n-5_installation-instructions-and-owners-manual_2404095045.webp)
39358-3-1019
Page 45
StANDING PILot oPeRAtING INStRUCtIoNS
ReMote/oFF/oN Switch
The fireplace is equipped with a REMOTE/OFF/ON switch. A
wire harness is attached to the REMOTE/OFF/ON switch. The
red, black and green (wires) female push-ons attach to the
REMOTE/OFF/ON switch. At the opposite end of the wire harness,
the black and green (wires) female push-ons attach to the gas valve.
An additional green wire and the red wire, which are stripped and
bare, will attach to one of the accessories that can be purchased
for use with your fireplace.
operation of ReMote/oFF/oN Switch with no Accessories
To ignite main burner, turn the control knob on the gas valve from
the PILOT position to the ON position. Turn the REMOTE/OFF/ON
switch from the OFF position to the ON position. The additional
green wire and red wire, which are stripped and bare are not used.
Wall Switch, FWS-1
Connect the green and red, stripped and bare, wires on the REMOTE/
OFF/ON switch wire harness to the wall switch using wire nuts. Turn
the REMOTE/OFF/ON switch to the REMOTE position. Pivot the
rocker switch on the FWS-1 to the ON position.
Wall thermostats (optional)
TRW - Wireless for Millivolt models
TMV - Reed switch for Millivolt models
Battery operated Remote Controls, FRBC, FBRtC, and tRW
Connect the green and red, stripped and bare, wires on the
REMOTE/OFF/ON switch wire harness to the remote receiver that
is a component in the remote kit using wire nuts. Turn the REMOTE/
OFF/ON switch to the REMOTE position. Follow instructions included
with the remote to complete installation.
Note: If batteries fail in the remote, and immediate heat is desired,
turn the REMOTE/OFF/ON switch from the REMOTE position to
the ON position.
electric (120 volt) operated Remote Control, FReC
Connect the green and red, stripped and bare, wires on the REMOTE/
OFF/ON switch wire harness to the wires on remote receiver that
is a component in the FREC using wire nuts. Turn the REMOTE/
OFF/ON switch to the REMOTE position. Follow instructions in the
FREC to complete installation.
NotICE:
If electric (120 volt) fails in FREC, and immediate heat
is desired, turn the REMOTE/OFF/ON switch from the REMOTE
position to the ON position.
Installation of Remote Receiver
Place remote receiver on the floor of fireplace behind the louver as
far forward as possible.
Attention:
The Velcro loop and hook are not necessary in this
installation but can be used to secure remote receiver.
Refer to remote control installation and operating instructions for
more details on remote control.
Millivolt Control
The valve regulator controls the burner pressure which should be
checked at the pressure test point. Turn captured screw counter
clockwise 2 or 3 turns and then place tubing to pressure gauge over
test point (Use test point “A” closest to control knob). After taking
pressure reading, be sure and turn captured screw clockwise firmly
to re-seal. Do not over torque. Check for gas leaks.
Millivolt thermopile is self generating. Gas valve does not require
24 volts or 110 volts.
Check System operation
Millivolt system and all individual components may be checked with
a millivolt meter 0-1000 MV range.
It is important to use wire of a gauge proper for the length of the wire:
Recommended Wire Gauges
Maximum Length
Wire Gauge
1' to 10'
18
10' to 25'
16
25' to 35'
14
MILLIVoLt SYSteM oPeRAtING INStRUCtIoNS
(CoNt’D)
Summary of Contents for DVP36FP30N-5
Page 20: ...39358 3 1019 Page 20 Figure 29 Figure 30 Figure 31 EXAMPLES TOP VENT RUN...
Page 37: ...39358 3 1019 Page 37 Figure 57 DVVK 4FV DIRECT VENT TERMINATION KIT CONT D...
Page 46: ...39358 3 1019 Page 46 Figure 70 MILLIVOLT SYSTEM STANDING PILOT WIRING DIAGRAM...