manualshive.com logo in svg

Emotion Tech MicroDelta Rework, User Manual, Page: 8 / 42

Share
Download
Emotion Tech MicroDelta Rework User Manual Download Page 8

8

PREPARATION

Documentation Version 1.2.6

Files to copy on the TF card

1°) Go to the eMotion Tech’s website support section, then go to «MicroDelta Rework / Software / Configuration» and download the correspon-

ding configuration files to your MicroDelta Rework depending on it’s version and options.

 

2°) Connect your printer to the computer

 

3°) Once downloaded, unzip the file and copy all its content in the eMotronic’s  TF card.

Objective :

 copy the required files in the eMotronic’s TF card.

Note: TF card is usually automatically detected and its content displayed once you connect your 3D printer to you computer. The 

TF card generally appears as drive «NO NAME» but this can vary depending on your hardware.

4°) Press the «Reset» button on the 3D printer (located on one side of the lower plate).

Mac OS X : what you should have on the TF card after this step

5°) Check that the device has been properly recognized by your operation system.

Summary of Contents for MicroDelta Rework











































Reviews:

No comments