background image

-19-

Common troubles and shooting

Phenomenon

The product out of work

Whether the power supply  is plugged in or

the leakage protector is disconnected.

No water outflow  from nozzle or the water

yield is very

Please press the stop button and

wait for the water supply.

Switch the power supply

Please sit down in a correct position.

It's a common phenomenon.

Please open the water-inflow

valve  if it is closed

Please clean or replace the filter

device if it is blocked

The  sensor is unsensible that someone sit on

The nozzle stops spraying after cleaning for

a period of time, then recover automatic

after 120 seconds.

If the user moves too fast or leaves the seat, 
the seat sensor cannot detect in a short time.

The filter may be blocked

Clean the filter screen or replace

the filter

Check the hose and tighten it

It's a common phenomenon.

The water-inflow hose may leakage

The seat sensor is unsensible and  no

deodorization voice

Sit back on the seat sensor

detection position.

Remove the deodorizing window

to clean or replace the activated

carbon filter.

Please close to the position of the

sensor as far as possible when

you use it.

Adjust the seat temperature with

remote control.

Adjust the water temperature with

remote control.

The water’s temperature is a little

cold when it just sprays.

Adjust the drying temperature with

remote control.

Activated carbon filter block or spacer may

be blocked

The seat sensor is not sensitive to the user.

Lower  seat temperature  is set.

Lower  water temperature  is set.

The water is a little cold when it just sprays.

Lower  drying temperature  is set.

The deodorant function will be continue to

work for 20 seconds in order to remove

the residual odor after the user leaves.

Sit back on the seat sensor detection
position,then start the relevant button

No response when press

the  the button of Posterior

cleaning &feminine

cleaning &drying 

The nozzle stops cleaning

suddenly when it's on work.

The nozzle stops cleaning

suddenly

Low water pressure when

Posterior cleaning or

feminine cleaning.

Deodorization effect is not

obvious

Deodorant function

continues to work after

user leaves

The toilet seat can't be heated

Cold water of Posterior

cleaning and feminine cleaning

The drying temperature is

not enough.

Reasons

Measures

Summary of Contents for B01 Series





























Reviews: