Emil Lux 420610, Manual

Page: 21 / 72

21
• Check the plug and cable before each use.
• If the power cable is damaged immediately dis-
connect the plug. Never use the device if the
power cable is damaged.
• If the device is not in use make sure the plug is
pulled out.
• Make sure that the device is switched off before
plugging in the mains cable.
• Make sure that the device is switched off before
unplugging it.
• Disconnect the power supply before transport-
ing the device.
Maintenance
• Before conducting any maintenance on the
device, disconnect the mains plug.
• Only those maintenance and fault elimination
tasks described here may be carried out. Any
other tasks must be completed by a specialist.
• Only use original replacement parts. Only these
replacement parts are designed and suitable for
the device. Other replacement parts will not only
lead to an invalidation of the warranty, they may
also endanger you and your environment.
Device-specific safety instructions
• Do not subject the device to rain. Do not use the
device in wet surroundings.
• Do not use the device in areas where there is
danger of explosion or in the vicinity of combus-
tible liquids or gases!
• Do not aim the water jet directly toward the
device or other electrical components! Mortal
danger due to electric shock!
• Lay the extension cord in such a way that it can-
not get into the liquid being conveyed.
• Do not install or turn on the device if there are
people or animals in the conveying medium (e. g.
swimming pool) or making contact with the con-
veying medium.
• Do not leave the device unsupervised. Unplug
the mains plug during periods of extended
absence.
• As a general rule, repairs are only to be carried
out by an electrician. If repairs are performed
improperly, there is danger of liquid getting into
the electronic components of the device.
• Remember that moving parts may also be
located behind ventilation and venting slots.
• Symbols affixed to your tools may not be
removed or covered. Information on the device
that is no longer legible must be replaced imme-
diately.
Your device at a glance
►
P. 3, item 1
1. Intake
2. Water drain plug
3. Pressure joint
4. Handle
5. On-Off switch
6. Filter housing
Scope of delivery
• Garden pump
• Instructions for use
Unpacking and commissioning
Setting up
• The device must be placed on a horizontal, level
surface that is sufficiently capable of supporting
the total weight of the device when filled with
water.
• To prevent vibrations, the device should be
placed on an elastic base [support] (e. g. a rub-
ber mat).
• The installation site must be well ventilated and
protected from the effects of weather.
• When being used on garden ponds and swim-
ming pools, the device must be set up so as to
guard against overflowing and protect against
falling in. Additional legal requirements must be
observed.
• When operating indoors you must ensure that
there is a drain in the floor or a leak prevention
mechanism.
• Before starting up, check the suction hose to
ensure that it is sealed. Bubbles of air in the suc-
tion hose are an indication that there may be
leaks and may lead to failure of the device!
Connect suction line
• All connections must be sealed with hemp and
thick paste (Fermit) or thread sealing tape (e. g.
Teflon tape); leaks cause air exhaust and reduce
or prevent water exhaust.
• Hemp should be used in case of pipe threads
from metal; synthetic thread must be sealed with
thread sealing tape.
• All components of the suction line must be pro-
fessionally installed.
• The suction pipe should have an internal diame-
ter of at least 25 mm; it must be kink resistant
and suitable for vacuum use.
• The suction line should be as short as possible,
since the conveying capacity decreases as the
length of the line increases.
• The suction line should ascend steadily toward
the pump to prevent air pockets.
• Sufficient water supply must be assured; the end
of the suction line must always be in water.
Read and observe the operating instruc-
tions before commissioning.
NOTICE! Risk of damage to the device!
The suction line must be installed so that it
does not exert any mechanical force or ten-
sion on the pump.
If the conveying medium is contaminated, a
suction filter must be used to protect the
pump from sand and dirt.
Note:
A check valve is recommended so
that the water does not run off when the
pump is shut off.
GB
Gartenpumpe_420610_420611.book Seite 21 Donnerstag, 17. September 2015 11:22 11