Emerson VOLTA CF590BQ00 Owner'S Manual Download Page 29

Page: 29 / 34

TROUBLE PROBABLE CAUSE SUGGESTED REMEDY

1. Fan will not start.

1. Loose power line connections to the fan, 1. Check line wire connections to fan and switch

or loose switch wire connections in the wire connections in the Light Kit Adapter.
Light Kit Adapter.

2. Reversing switch in neutral position. 2. Make sure reversing switch position is all the

way to one side.

2. Fan sounds noisy.

1. Blades not attached to fan. 1. Attach blades to fan before operating.

2. Wire connectors inside Light Kit 2. Check to make sure wire connectors in Light

Adapter are rattling. Kit Adapter are not rattling against each other or

against the interior wall of the Light Kit Adapter.

3. Screws holding blades to motor hub 3. Tighten screws securely.

are loose.

3. Fan wobbles

1. Setscrews in motor coupler are loose. 1. Tighten both setscrews securely in the motor coupler.

excessively.

2. Setscrew in hanger ball/downrod 2. Tighten the setscrew in the hanger ball/downrod

assembly is loose. assembly.
3. Screws securing fan blades to 3. Check to be sure screws which attach the fan blades

motor hub are loose. to the motor hub are tight.
4. Hanger bracket and/or ceiling outlet 4. Tighten the hanger bracket screws to the outlet box,

box is not securely fastened. and/or secure outlet box.

16. Troubleshooting

FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE

TROUBLESHOOTING YOUR FAN.

WARNING

Make sure main power is turned OFF.

WARNING

Make sure main power is turned OFF.

WARNING

emersonfans.com

Please contact 1-800-654-3545 for further assistance

ETL Model No.: CF590

Do not use water when cleaning your ceiling fan.

It could damage the motor or the blades and create the

possibility of an electrical shock.

WARNING

IMPORTANT CARE INSTRUCTIONS

for your Ceiling Fan

Periodic cleaning of your new ceiling fan is the only

maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth to

avoid scratching the finish.
Abrasive cleaning agents are not required and should be

avoided to prevent damage to finish.

15. Maintenance

Summary of Contents for VOLTA CF590BQ00



































Search results

Summary of Contents for VOLTA CF590BQ00

Reviews:

Related manuals for VOLTA CF590BQ00

Brands by name

Popular brands

Emerson VOLTA CF590BQ00, Owner'S Manual

Search results

Summary of Contents for VOLTA CF590BQ00

Reviews:

Related manuals for VOLTA CF590BQ00

Brands by name

Popular brands