Emerson Rosemount Xi Reference Manual Download Page 25 | Manualshive

Page: 25 / 82

background image

Figure 2-9: Power connections - Rosemount Xi Advanced Electronics

A. From DR board for Traditional Architecture configurations

B. Power Supply Board

9. If your system is configured for two channel operation, repeat steps 2 through 7 to

connect the other signal wires.

10. Remove the connector from the power supply board located on the left-hand side

of the card rack inside the Rosemount Xi.

11. See

. Connect the line, or L1, wire to the L1 terminal and the neutral, or

L2, wire to the N terminal.

12. Reinstall the power supply connector in the power supply board.

13. Close and fasten the Rosemount 736 °C Roseount Xi cover.

2.3.1

Wire the traditional architecture cable connections

A traditional architecture configuration is used to provide for remote location of the
transmitter electronics. All electronics are housed inside the Rosemount Xi. A multi-
conductor power/signal cable connects between the probe and the Rosemount Xi. Use the
following procedure to connect the traditional architecture probe to the Rosemount Xi.

NOTICE

The traditional architecture cable is provided at the specified length and is ready for
installation. The cable glands must be properly terminated to maintain EMC/EMI noise
protection.

1. Run the 7-conductor cable between the traditional architecture probe and the

installation site for the Rosemount Xi. Use new cable conduit or trough as needed.

2. Install the cable and lead wires to the probe per manufacturer's instructions.

Reference Manual

Install

00809-0100-4889

October 2022

Emerson.com/Rosemount

25

«
...
23
24
25
26
27
...
»

Summary of Contents for Rosemount Xi



















































































Reviews:

No comments

Related manuals for Rosemount Xi

Brand: Keithley Pages: 48

BML SL1-ALZ-ZZ Series

Brand: Balluff Pages: 26

Brand: Valhalla Scientific Pages: 43

Brand: Major tech Pages: 16

Brand: Zoetis Pages: 2

Brand: Panasonic Pages: 1

Brand: Jula Pages: 9

LISST-PORTABLE XR

Brand: Sequoia Pages: 41

Brand: ESP Pages: 12

Brand: Cal Test Electronics Pages: 12

Brand: Lutron Electronics Pages: 43

Brand: IDT Pages: 20

Brand: Omega Pages: 26

LiveTester LT 220

Brand: StarLogixs Pages: 7

Brand: Hanna Instruments Pages: 28

Brand: Kawai Pages: 2

LaserRange-Master T4 Pro

Brand: LaserLiner Pages: 68

Brand: Niigata seiki Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands